Tyler you need to remember he is running a TIGHT stall, 2400 is very low and that cam will come on hard at 2400.
Tyler you need to remember he is running a TIGHT stall, 2400 is very low and that cam will come on hard at 2400.
2007 CCSB Z71 VortecMax: Stock!
Cody--I just now read his sig--yeah, that cam will come on strong right with that stall--those PI stalls are tight! I guess for what Zeake wants, that cam will suit him perfectly...
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
Ok installing cam. Do you have to pull the heads? My tech who has never worked on an ls1 says it is a better idea to pull the heads.. I didn't think we'd have to. It makes me want to buy heads.Dang that burning plastic stinks.
99RCSB Broke because I wasted thousands and thousands of dollars on my truck.
no, dont take off heads... here is a link on how to. LS1Howto.com for ls1 but the same for trucks
Last edited by ff_jeff; 03-21-2008 at 08:20 AM.
Yeah, no need. Just get some 5/16'' wooden dowel rods to stick into the oil galleys after you spin the cam to keep the lifters up. Then it is YOINK--and the cam comes right out. It is rather simple...
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
Sounds a lot better than 16 magnets or pulling the heads. Thanks whole bunch on that one.Originally Posted by txarkitekt
99RCSB Broke because I wasted thousands and thousands of dollars on my truck.
More questions. Would a high perf oil pump add life to the motor? If so what oil pump would you purchase and any thing else need to be done after adding a high perf oil pump? I figure the best thing to do is everything I can afford to do while the motor is out. Even if it means a couple hundred in plastic.
99RCSB Broke because I wasted thousands and thousands of dollars on my truck.
If you have good oil pressure I would not waste the money on the oil pump. Take the wife out for a nice dinner on that plastic to thank her for understanding your craving for power!
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
Thanks Red
99RCSB Broke because I wasted thousands and thousands of dollars on my truck.
Since the motor is on the engine stand no need to put dowels in or anything flip the motor upside down spin the cam pull it out and put the new one in.
2007 CCSB Z71 VortecMax: Stock!
Posting Permissions
Reply With Quote
