i just got to rocky point! and went to the sand hill to mess around, and just found out that my truck wont go to 4WD LOW!!! everyone is now kicking the **** out of me!!! i just put my new nelson's PCM, shift kit, and servo in... and i dont know why it wont go into 4wd LOW!!! what can i do to fix it??? help pleasee!! i've been doing investments in my truck the whole year for this week, and now it wont work... i cant believe it.. what can i do?? please buds.. help me out with this..
06' Silverado RCSB 5.3L 4wd..
PERFORMANCE: Cam, Springs, Pushrods, P&P heads & 3 angle valve job, Injectors, PS LT's & ORY, Nelson Tune, Catback, CAI, Comp Cam Double Timing Chain, HP Oil Pump, UD Pullies, ARP bolts, Stall, TBS, 4.10's, Iridium NGK's, G-80, 160 t-stat, HD-2 & Vette Servo, 46,000 tranny cooler, 75-125hp shot of funny Gas..
HID's Hi, Lows & Fogs
Waiting to be installed: LC-1 WB & Standalone system
Did you put it into neutral will trying to switch
yes sir i did!!! i put it in neutral!! i dont know what to do!!
06' Silverado RCSB 5.3L 4wd..
PERFORMANCE: Cam, Springs, Pushrods, P&P heads & 3 angle valve job, Injectors, PS LT's & ORY, Nelson Tune, Catback, CAI, Comp Cam Double Timing Chain, HP Oil Pump, UD Pullies, ARP bolts, Stall, TBS, 4.10's, Iridium NGK's, G-80, 160 t-stat, HD-2 & Vette Servo, 46,000 tranny cooler, 75-125hp shot of funny Gas..
HID's Hi, Lows & Fogs
Waiting to be installed: LC-1 WB & Standalone system
Check all fuses, crawl under the truck and see if maybe the solenoid got unplugged when the tranny guy was putting in the new shift kit. Follow the wires and see that they didn't get cut, crimped or melted.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
Yeah, I was thinking the same. There has to be something that was not plugged in somewhere... So, does it go into 4 HI? That is weird because the 4WD actuator should send it to 4HI or 4LO no matter what... Check your connections at the actuator and see if any wires were damaged or crimped.
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
faulty dash switch? We all know that they're not known for lasting forever...
yes, it goes in 4wd HI, but when i try to put it in LOW, i can hear the 4wdLOW noise when it is hooked, but then again, does the same noise and get the LOW out again...
06' Silverado RCSB 5.3L 4wd..
PERFORMANCE: Cam, Springs, Pushrods, P&P heads & 3 angle valve job, Injectors, PS LT's & ORY, Nelson Tune, Catback, CAI, Comp Cam Double Timing Chain, HP Oil Pump, UD Pullies, ARP bolts, Stall, TBS, 4.10's, Iridium NGK's, G-80, 160 t-stat, HD-2 & Vette Servo, 46,000 tranny cooler, 75-125hp shot of funny Gas..
HID's Hi, Lows & Fogs
Waiting to be installed: LC-1 WB & Standalone system
Hmmmm...sounds fishy. I would check all of your wiring connections down there. By doing a servo and shift kit, you should have not even touched the 4WD stuff...
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
Posting Permissions
Reply With Quote
