All LS Based Conversions
Starting this to answer as many questions as I can in one place. I am trying to compile the most complete list of what to do to complete a conversion...
Hey Guys, these questions get asked quite a bit, and what better way than to make a sticky with all the part numbers you'll need. I'm open to...
2001 silverado (Thanks Banker099) This image has been resized. Click this bar to view the full image. The original image is sized 799x247...
Couple of questions? 1) the vapor purge valve on front of intake can we get rid of this or is it something needed? If I do keep it does it tie in...
I'm new here and i'm doin a conversion useing a 2003 5.3 and 4l60e . My question is now that i have removed the un needed wires from the harness i...
I am swapping a 4.3 in a 2006 silverado 1500, to a 6.0 LQ4 from a 2002 2500 I have engine, fuse box, pcm, and harness from the 2500, am I better to...
I'm going to post what I did to mate my nv3500 to my 5.3 since I wasn't able to find any reliable info when I did my swap. I bought the flywheel from...
If I go with a computer from an LS1 for my 5.3, can I use one that was for a 6 speed car and have it programmed? As of now, the only computer I have...
Hello all, I completed an 8.1L swap last year in a 70’s GM truck using a MEFI-4 ECM. Never got that damn thing tuned right so I just replaced ...
Hello. New member here. I finally brought home my 5.3 & 4L60E in my minivan since my truck's 4-banger is knocking. The 2nd 4L60 is for my buddy....
Hi Everyone. Swapped a 5.3 from a 2002 Tahoe into our 97 2 door Tahoe. We have been driving the thing all over the place because it is so much fun...
1988 k2500 5.7 recently started knocking. So what I wanted to know would it be more sufficient to put another 5.7 in it? Or I have a 4.8 and do a...
So, I just want to put this out there before anyone else gets screwed over by this *******. Johns custom wiring 475 E South Airport Rd Traverse...
I just finished making an A/C bracket kit that will allow the stock A/C compressor and lines to be used when doing a Gen3 install. I have seen a lot...
I have been searching for what I need for a year and no one makes it. (that I can find) The closest Ive seen is LSX innovations one thats for an LT...
What did everyone use to keep the AC working after swapping the motor? I pinned the AC wires to the new PCM but I dont have the AC request signal...
Looking for insight on some headers for my 1995 k1500 rcsb… I’d really like a set of long tubes preferably stainless steel… I have read that the...
New to the site. I am swapping a 88 C1500 to 6.0 and 4l60. All the headers I am finding say they will work on 2wd only. Have any of you guys used the...
Hi guys, I have a 94 Silverado I'm putting a aluminum LS1 into and I have a few question about the gauges. I have removed the old TBI harness that...
Ok so I've seen a couple of you do it , but for the life of me can't find the exact threads on it. What steps did it take to use this transmission...
I am new to site, heard I can get some much needed accuurate, effecient and useful help and information for my 0411 swap. I am looking for the golden...
There was a gent on the forum (I believe) that would reprogram your pcm. Remove rear O2, egr , adjust speedo for gear ratio and tire size and trans...
I have a drive by wire TBSS intake . I purchased the adapter to convert wiring to work with tbss from summit when you turn key to run position the...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
