+ Reply to Thread
Page 1 of 3 1 2 3 LastLast
Results 1 to 10 of 24

Thread: Q#$%@#&^%^*%&@#$

Hybrid View

  1. 03-02-2007 10:48 PM #1
    1BADC10's Avatar
    1BADC10
    1BADC10 is offline Senior Member
    Join Date
    Oct 2005
    Location
    Baton Rouge, LA
    Posts
    997
    All I have to say right now is that I'm one unlucky mutha-----!








    I'll be up early tomorrow morning disassembling the motor in my Yukon. I'll need the following:

    fuel line removal tool
    cherry picker
    engine stand
    manpower

    For those who haven't heard, the Yukon's 5.3 was jealous, and decided to possibly throw a rod. I don't know for sure, but different sources tell me the same possibility. I'm going to try to calm my anger before I take a sledgehammer to my daily driver. One thing's for sure, I'm glad this happened close to home, but pissed that it happened to an untuned STOCK motor!
    Test-n-Tune (Nov 23, 2008) - 13.65s @ 98mph
    Reply With Quote Reply With Quote
  2. 03-02-2007 11:03 PM #2
    RedHeartbeat
    RedHeartbeat is offline WTH JUST HAPPENED?
    Join Date
    Nov 2003
    Location
    Denton Texas
    Posts
    20,540
    So I guess there wasn't a warranty?
    See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
    Reply With Quote Reply With Quote
  3. 03-02-2007 11:14 PM #3
    1BADC10's Avatar
    1BADC10
    1BADC10 is offline Senior Member
    Join Date
    Oct 2005
    Location
    Baton Rouge, LA
    Posts
    997
    Uh... no. Yukon has 111K miles on it. I bought it new in '02 with 7 miles on the dial.
    Test-n-Tune (Nov 23, 2008) - 13.65s @ 98mph
    Reply With Quote Reply With Quote
  4. 03-02-2007 11:21 PM #4
    RedHeartbeat
    RedHeartbeat is offline WTH JUST HAPPENED?
    Join Date
    Nov 2003
    Location
    Denton Texas
    Posts
    20,540
    gonna pull the engine from the c10 and put it in the Yukon since the transmission is crap in it anyway or just find a salvage engine?
    See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
    Reply With Quote Reply With Quote
  5. 03-02-2007 11:50 PM #5
    1BADC10's Avatar
    1BADC10
    1BADC10 is offline Senior Member
    Join Date
    Oct 2005
    Location
    Baton Rouge, LA
    Posts
    997
    Looks like I may have to if I want a running DD for Monday morning.

    However, if I do this, you can bet that I'm putting the STOCK cam & heads on the shortblock. I'm not too keen on swapping the shortblock b/c the two bottom bolt-hole threads on the block are stripped out. I was thinking of tapping new threads, but no sure if that's wise.

    This is THE WORSE time to have something go wrong with my DD. I can't believe this crap!
    Test-n-Tune (Nov 23, 2008) - 13.65s @ 98mph
    Reply With Quote Reply With Quote
  6. 03-02-2007 11:55 PM #6
    outlaw_king's Avatar
    outlaw_king
    outlaw_king is offline Horse Power Lover....
    Send a message via Yahoo to outlaw_king
    Join Date
    Dec 2006
    Location
    Saginaw, Texas
    Posts
    607
    damn man hate to see that, would be happy to lend you a hand to get it back together by monday but Baton Rouge is a little far for me to help with...
    I am gonna be a new Daddy...

    Drive it like you live hard and fast....
    '91 rcsb, 4.3 V6, 700R4 trans swap, 4/6 drop rolling on 18's, roll pan, 2" cowl hood, electric fan, TBI injector spacer, K&N filter replacement, flowmaster muffler...



    [Today 08:09 AM] ChevyLee: dale would make a awesome dad in law too
    Reply With Quote Reply With Quote
  7. 03-03-2007 12:13 AM #7
    RedHeartbeat
    RedHeartbeat is offline WTH JUST HAPPENED?
    Join Date
    Nov 2003
    Location
    Denton Texas
    Posts
    20,540
    You need a helicoil kit to repair the threads. That's the best way to handle the stripped threads.
    See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
    Reply With Quote Reply With Quote
  8. 03-03-2007 06:51 AM #8
    1BADC10's Avatar
    1BADC10
    1BADC10 is offline Senior Member
    Join Date
    Oct 2005
    Location
    Baton Rouge, LA
    Posts
    997
    <div class='quotetop'>QUOTE(RedHeartbeat &#064; Mar 2 2007, 11&#58;13 PM) [snapback]85061[/snapback]</div>
    You need a helicoil kit to repair the threads. That&#39;s the best way to handle the stripped threads.
    [/b]
    Noted... where can I get this kit?
    Test-n-Tune (Nov 23, 2008) - 13.65s @ 98mph
    Reply With Quote Reply With Quote
  9. 03-03-2007 08:35 AM #9
    twobit
    twobit is offline Senior Member
    Send a message via AIM to twobit
    Join Date
    Apr 2003
    Location
    Allen, Tx(DFW)
    Posts
    445
    Autozone and OReillys has them I believe but not sure if they will have the right size.
    02 Silverado
    02 TrailBlazer
    Reply With Quote Reply With Quote
  10. 03-03-2007 09:43 AM #10
    RedHeartbeat
    RedHeartbeat is offline WTH JUST HAPPENED?
    Join Date
    Nov 2003
    Location
    Denton Texas
    Posts
    20,540
    Take one of the bolts with you and they can match it up. I think its 8mm x 1.25mm pitch.
    See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
    Reply With Quote Reply With Quote
+ Reply to Thread
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules