my first ls swap 1996 2 door Tahoe 4wd 385 Stroker to LQ4 cam headers **pics**

[Minime168]

yea i got it now i was looking there but i dont have a tailshaft because its 4wd. its in the transfer case. i havent checked it yet to see if its the same plug. but if not ill probably have to grab it off the stock harness for the truck. dude i saw your video thats awesome. win any races yet?

Hahaha nah never raced her!

[myzterray]

Hahaha nah never raced her!

ahhh thats no fun...soon as i get mine running im racing someones truck..im pretty sure with the tune/headers/cai i should be able to embarass a few nnbs tahoes and silverados out there

[pl4yboy]

ahhh thats no fun...soon as i get mine running im racing someones truck..im pretty sure with the tune/headers/cai i should be able to embarass a few nnbs tahoes and silverados out there

Be careful... not all of us are 5.3s and 4.8s.

[myzterray]

Be careful... not all of us are 5.3s and 4.8s.

lol yea gotta watch out for those 6.2s.

[myzterray]

ok so i took a week off from working on this thing. actually went outta town for a short vacay. im back and ready to get this thing finished up. got my dirty dingo mounts in the mail and they work perfect. should have used these in the first place!





also i had to drop the tran because i used the wrong bolts to hook up the flywheel spacer to the back of the motor. so i dropped the trans and installed the new bolts.




also theres a shot of one of the holes i had to make longer to make the 5.3 flywheel work with my older 4l60.

i also ordered the vacuum adapter fitting from gmpartsgiant.com..the part was only like 4 bucks but they charge 11 bucks for shipping and once i got the package i seen why...they used this huge box wirth a huge envelope inside to ship a part no bigger than a AA battery smh!

[RedHeartbeat]

I put a chain through the balancer and to the frame and then take the handle from my floor jack and slip it over my breaker bar to loosen the bolt. Goes from the drivers side fender towards the passenger side when the breaker bar handle is is pointed up.

[myzterray]

I put a chain through the balancer and to the frame and then take the handle from my floor jack and slip it over my breaker bar to loosen the bolt. Goes from the drivers side fender towards the passenger side when the breaker bar handle is is pointed up.

i did the same thing. i used the hoist chain and used the jack handle and it came off. so now to autozone to rent the puller. wasnt that bad.

[SEREOUS67]

Also a small 6 gallon or larger compressor works wonders. I have a 13 gallon (used $35) and it helped me R&R my stock suspension to a 6 inch lift plus 3 inch body lift. All done by myslef. Invest in small but quality tools. Keep up the progress bruh.

[pl4yboy]

When we did mine, a compressor wasn't enough. It took a 4' cheater to break mine free.

[myzterray]

Also a small 6 gallon or larger compressor works wonders. I have a 13 gallon (used $35) and it helped me R&R my stock suspension to a 6 inch lift plus 3 inch body lift. All done by myslef. Invest in small but quality tools. Keep up the progress bruh.

yea im in the middle of relocating to another state so cant really spend too much on tools. finally getting out this stupid apartment and getting a conda with a garage! then the fun will begin. i got a 68 mallibu i want to do a frame off restoration too. but everything been on hold while i wait on some parts to come in the mail. hopefully when i get everything together this thing runs