Crane Cam 216/224

[ThumpinZ]

pm me with a # and I can send audio/video with my phone. I don't have a card to get it from my phone to the comp because the micro port is trashed. Or go here http://www.youtube.com/watch?v=DnvkKxCXjVM But this guy has no cat's so you know how sound goes when you remove those. Wish I could but I can't darn emissions... Either way this guy has the same cam.

Hows the cam sound???? Im thinking of getting a cam i have no idea what one tho yet haha?????

[darnie1987]

Pm sent... Ya i wanto get one here b4 too long, i have 100k on my motor, 5.3, shortie headers for now, cai, nelsoned tuned, and cat back. Just need sumthing reliable with a nice sound and decent power gains. Its still my dd, but i dont have to drive all that far.... Wanto get atleast 15 mpg tho im getting around 20-22 now so should be fine

[ThumpinZ]

Here's a parts list and the pricing I paid. If anyone else needs it. Don't forget if your not takin the heads off you'll need an in car spring compressor I like the dual valve tool about $120 at Vinci. Also the Crane valve locks were on back order last time I checked you can have your supplier cross ref them with Comp Cams which tend to be more readily available.

Parts from Summit Racing
-Crane Valve Springs crn-144832 $160
-Crane Steel Retainers crn-144944 $66
-Trick Flow Push Rods 7.4 tfs-21407400 $87
-Crane Valve Locks CRN-99107 $33

Parts Store or Dealer
-Crank bolt $6
-Timing chain cover gasket set $40
-Valve cover gaskets $13

CAM
At Summit part # crn-1449561 it is priced at $468.95 can pick it up from Vincihiperformance.com for $405 known as the Trucker

Looking at about $800 to a grand. Depending on part cost and shipping in your location.

Ofcourse you'll need a tune to compliment your setup, that's up to you. I had mine dyno tuned at MTI Racing in Marietta Ga. If your in the GA area there is also Vengeance, Atlanta Performance and Dynolab that I know of. All located on the northside.

[beingblueeyes]

hey ThumpinZ,
Have you hade your tune dialed in after the cam install? I ask because I was reading “truckin” magazine volume 36 #9 (this months GM vs ford vs dodge) and came across a project of there’s called "novakane" were they took a 04 sierra with a 4.8 5 speed (with slipping clutch so say the article) with over 110k on the clock and are building a sport truck out of it. they have much of what you have but different makers. On the 4.8 they have
banks monster exhaust
bank torque tube headers
banks ottomind programmer
(seeing a trend here)
banks ram air intake
and it put down 257hp and 286tq at the wheels after the mods
now i know you have higher miles then that truck and a auto trans but you also have a 5.3 to his 4.8 and a cam and h pipe
Not trying to pick a fight, just trying to make sure you get all the HP your paying for

[ThumpinZ]

Those numbers were after all mods and tune. I did the install myself, just had MTI tune it. I'd like more I would atleast to make 300 to the wheel before she is retired for a 6l

hey ThumpinZ,
Have you hade your tune dialed in after the cam install? I ask because I was reading “truckin” magazine volume 36 #9 (this months GM vs ford vs dodge) and came across a project of there’s called "novakane" were they took a 04 sierra with a 4.8 5 speed (with slipping clutch so say the article) with over 110k on the clock and are building a sport truck out of it. they have much of what you have but different makers. On the 4.8 they have
banks monster exhaust
bank torque tube headers
banks ottomind programmer
(seeing a trend here)
banks ram air intake
and it put down 257hp and 286tq at the wheels after the mods
now i know you have higher miles then that truck and a auto trans but you also have a 5.3 to his 4.8 and a cam and h pipe
Not trying to pick a fight, just trying to make sure you get all the HP your paying for

[gavin05]

this is same cam that i got in my 4.8

[darnie1987]

what do u think i could pull out of the cam numbers wise with the cam swap and a nelsons 91 tune on it?