All 16 of mine tick and the injectors click and clatter like an old sewing machine.
All 16 of mine tick and the injectors click and clatter like an old sewing machine.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
not sure yet, sounds like the same spot. Just let the truck get warm and run for 20min and no tick.Originally Posted by txarkitekt
I am gonna run around in it to day and see what it does. I will just watch the A/f really close.
Name: Mark,
God created turbo lag so nitrous trucks could have a chance.
http://www.ls1truck.com/forums/my-ga...tml#post274877
I have lifter ticking as well. Some times the lifter tick really loud and then go away.
Truck 2002 Chevy with
old setup KB turbo kit MP70 LS1
New setup stock for now
by any chance did the lifter spin in the holder last time?
2002 Lightning - GT headed 5.5Litre w/ Twin 7665s
2002 Silverado - 427Lsx w/ Twin gt4202s
2010 Silverado crewcab Z71 - 5.3litre w/ procharger
2000 Wrangler - 5.3litre with some stance
2014 Xsport- 3.5 Eco boost
412 Motorsports
it ain't that I'm too big to listen to the rumors, It's just that I'm too damn big to pay attention to 'em..That's the difference
I cant really say. But the lifter cup/trays looked ok, i didn't see any cracks to speak of.
Name: Mark,
God created turbo lag so nitrous trucks could have a chance.
http://www.ls1truck.com/forums/my-ga...tml#post274877
DOOOOOOOOOD! I would have replaced the lifter trays!!!!!
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
of course you say that now where were you a week ago before the swap, thanks homie.
Name: Mark,
God created turbo lag so nitrous trucks could have a chance.
http://www.ls1truck.com/forums/my-ga...tml#post274877
like i said my motor makes a similar noise. i just did the typical check up on it and all check out good. its a bad lifter and mine is up front on passengerside
2002 Lightning - GT headed 5.5Litre w/ Twin 7665s
2002 Silverado - 427Lsx w/ Twin gt4202s
2010 Silverado crewcab Z71 - 5.3litre w/ procharger
2000 Wrangler - 5.3litre with some stance
2014 Xsport- 3.5 Eco boost
412 Motorsports
it ain't that I'm too big to listen to the rumors, It's just that I'm too damn big to pay attention to 'em..That's the difference
Well, I guess it was an assumption that you do that when you replace lifters. A metal piece being retained by plastic? Come on Marky Mark! Its like going though and replacing the brakes on one side of the car, when it is common knowledge that you replace the brakes on both sides... No worries man.
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
gotta remember this is my first rodeo with LS internals.
Name: Mark,
God created turbo lag so nitrous trucks could have a chance.
http://www.ls1truck.com/forums/my-ga...tml#post274877
Posting Permissions
Reply With Quote
