Does anyone know where can I find a nice set of bolts for my headers? Cause I am going to install them soon and I dont what to use my factory ones cause I've been told that the dont hold for too much.. anything else anyone would recomend for my install? any link would be appeciated!
Thanks!
06' Silverado RCSB 5.3L 4wd..
PERFORMANCE: Cam, Springs, Pushrods, P&P heads & 3 angle valve job, Injectors, PS LT's & ORY, Nelson Tune, Catback, CAI, Comp Cam Double Timing Chain, HP Oil Pump, UD Pullies, ARP bolts, Stall, TBS, 4.10's, Iridium NGK's, G-80, 160 t-stat, HD-2 & Vette Servo, 46,000 tranny cooler, 75-125hp shot of funny Gas..
HID's Hi, Lows & Fogs
Waiting to be installed: LC-1 WB & Standalone system
WWW.ARP-BOLTS.COM 10MM X 1.5 I believe.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
Thanks! just couldnt find the price or anything.. are the ones for "LS based engines"?
06' Silverado RCSB 5.3L 4wd..
PERFORMANCE: Cam, Springs, Pushrods, P&P heads & 3 angle valve job, Injectors, PS LT's & ORY, Nelson Tune, Catback, CAI, Comp Cam Double Timing Chain, HP Oil Pump, UD Pullies, ARP bolts, Stall, TBS, 4.10's, Iridium NGK's, G-80, 160 t-stat, HD-2 & Vette Servo, 46,000 tranny cooler, 75-125hp shot of funny Gas..
HID's Hi, Lows & Fogs
Waiting to be installed: LC-1 WB & Standalone system
anyone else can help me with a link? thanks
06' Silverado RCSB 5.3L 4wd..
PERFORMANCE: Cam, Springs, Pushrods, P&P heads & 3 angle valve job, Injectors, PS LT's & ORY, Nelson Tune, Catback, CAI, Comp Cam Double Timing Chain, HP Oil Pump, UD Pullies, ARP bolts, Stall, TBS, 4.10's, Iridium NGK's, G-80, 160 t-stat, HD-2 & Vette Servo, 46,000 tranny cooler, 75-125hp shot of funny Gas..
HID's Hi, Lows & Fogs
Waiting to be installed: LC-1 WB & Standalone system
really? arent they suppose to break??
06' Silverado RCSB 5.3L 4wd..
PERFORMANCE: Cam, Springs, Pushrods, P&P heads & 3 angle valve job, Injectors, PS LT's & ORY, Nelson Tune, Catback, CAI, Comp Cam Double Timing Chain, HP Oil Pump, UD Pullies, ARP bolts, Stall, TBS, 4.10's, Iridium NGK's, G-80, 160 t-stat, HD-2 & Vette Servo, 46,000 tranny cooler, 75-125hp shot of funny Gas..
HID's Hi, Lows & Fogs
Waiting to be installed: LC-1 WB & Standalone system
Break, I dont think the header bolts will break unless you over torque the crap out of them. I have been running the stockers, I did use a Mr.Gasket brand gasket. I see no need to use anything else.
Name: Mark,
God created turbo lag so nitrous trucks could have a chance.
http://www.ls1truck.com/forums/my-ga...tml#post274877
I have always used the stock metal 3-layer gaskets and bolts. Just don't torque the hell out of them when tightening and also make sure to tighten them perpendicular to the block...if you try and tighen them at an angle--they will break.
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
Posting Permissions
Reply With Quote
