What will I benefit most from 4:10's and a locker or pacesetter Lt's and ORY? Also where is the best place to purchasae this stuff Summit,Jegs.... Current mods in sig. All thoughts appreciated!
4:10's and locker or Lt's and ory?
What will I benefit most from 4:10's and a locker or pacesetter Lt's and ORY? Also where is the best place to purchasae this stuff Summit,Jegs.... Current mods in sig. All thoughts appreciated!
2006 extended cab, 6.0 swap, full bolt ons SOLD
2011 ECSB, 6.2, 6 spd, 3.73, 5" lift, 33" nitto, limo tint, debadged, volant CAI, muffler delete, black bear tune 14.0 @ 98 on the 33'sSOLD
2007 TBSS AWD, cam, stall, built trans, N2OSOLD
2006 RCSB cammed LQ9, full exhaust, 3200 stall, 2-4 drop
Originally Posted by farmtruc
49 Ford F1
355 chevy / turbo 350 / 12 bolt posi / camaro subframed
well thats a trick question. You would probably see alot better speed from the 4.10s. So if you are trying to get faster go with that. If you are trying to better your truck you could see improved gas mileage with a better exhaust and a better sound from your truck as well as a decent horsepower increase. So which do you prefer at this point in time is what you should ask yourself.
06 Intimidator SS- Tuned, CAI -DD
03 Silverado- Last incarnation 13.6... RIP
Ls1, Pnp heads, Polluter camshaft, spray, 4k stall on the way
"Seize the day like you seize your noodle" - Shin Chan
Better 1/4 times.
2006 extended cab, 6.0 swap, full bolt ons SOLD
2011 ECSB, 6.2, 6 spd, 3.73, 5" lift, 33" nitto, limo tint, debadged, volant CAI, muffler delete, black bear tune 14.0 @ 98 on the 33'sSOLD
2007 TBSS AWD, cam, stall, built trans, N2OSOLD
2006 RCSB cammed LQ9, full exhaust, 3200 stall, 2-4 drop
49 Ford F1
355 chevy / turbo 350 / 12 bolt posi / camaro subframed
Pacesetters and ORY are great... expect a helluva better sound. And 2-3 tenths off the 1/4. You will see an even better improvement over the strait pipe you have. Just get at least a single chamber muffler for a little back pressure. However, the 4.10's and locker will be a better mod. I wish i would have gotten them first. If you did not get the rear o2's deleted with your tune, you will need a retune so you dont get a check engine light. With ORY the rear o2's will flip out.
So My 2 cents says get the locker and 4.10's first. And then when you decide to get headers, get servo's, and some other stuff, then get a retune.
Thanks for the input I think I'm gonna get the gears and locker. Which locker do you recomend and where is the best place to get it?
2006 extended cab, 6.0 swap, full bolt ons SOLD
2011 ECSB, 6.2, 6 spd, 3.73, 5" lift, 33" nitto, limo tint, debadged, volant CAI, muffler delete, black bear tune 14.0 @ 98 on the 33'sSOLD
2007 TBSS AWD, cam, stall, built trans, N2OSOLD
2006 RCSB cammed LQ9, full exhaust, 3200 stall, 2-4 drop
49 Ford F1
355 chevy / turbo 350 / 12 bolt posi / camaro subframed
eBay Motors: GM 8.6 CHEVY 10 BOLT 4.11 RING AND PINION INSTALL PKG (item 330263169396 end time Sep-17-08 05:58:54 PDT) best deal... gears and install kit
eBay Motors: NEW DETROIT TRUETRAC GM 8.5 CHEVY 10 BOLT 30 SPLINE 8.6 (item 230268564733 end time Sep-03-08 17:04:42 PDT) locker... Rons has been good to us.
If you plan on going turbo, or whipple, might want to get 3.90's or 3.73's. But the 4.10's are needed for our smaller cube motors to get out of the hole... I have the 4.11's above, and will be getting the same locker... Ill be running a 150hp shot of nitrous and a cam...
Last edited by ff_jeff; 08-25-2008 at 09:14 PM.
Sweet, thanx Jeff!!
2006 extended cab, 6.0 swap, full bolt ons SOLD
2011 ECSB, 6.2, 6 spd, 3.73, 5" lift, 33" nitto, limo tint, debadged, volant CAI, muffler delete, black bear tune 14.0 @ 98 on the 33'sSOLD
2007 TBSS AWD, cam, stall, built trans, N2OSOLD
2006 RCSB cammed LQ9, full exhaust, 3200 stall, 2-4 drop
49 Ford F1
355 chevy / turbo 350 / 12 bolt posi / camaro subframed
no prob, it will cost you your rims though...
Last edited by ff_jeff; 08-25-2008 at 09:19 PM.
ID have to say gears, when i switched mine out was probably the best mod i ever did, to me i could feel more "seat of the pants power" then after my cam install, i know sounds crazy but 3.23 to 4.10s is an awesome jump
THEY CALL ME G.
AZRAEL
2017 RZR 1000 2 SEATER
2023 RZR 1000 XP 4
2008 LTZ DURAMAX 3500
2023 300S 5.7
2023 BUICK ENCORE[/B]
The difference between winning and losing, is having a 2nd stage.
just keep in mind the retune will have to be done no matter which route you go. LT Headers and ORY = Rear O2 Delete, retune. 4.10's and locker = gear change retune. If you are not in a position to install the LS, ring and pinion yourself, press, dial indicator and a lot of patience then you will need to tack on another 300-400 labor+parts. On the other hand the longtubes and ORY you can put on yourself in about 3 hours. Just my thoughts. Either way if you have the bug you will be doing both at some point, just depends on how much you want to spend on this mod go round!
Enjoy
Bryan
Posting Permissions
Reply With Quote
