I traded my 93 2wd for a 95 4wd. well i took it out playing in the mud last night and i couldnt get the 4wd to engage. My clutch is shot could that be my problem? the 4wd light dosent come one either when the selecter is moved. i no longer have the truck that is in my avatar, ill get some new pics shortly. Thanks for any input. i also need some KC's for it if any bodys got some.
Daily driver: '97 Z-71 reg. cab, electric fans, dual bats, K&N cold air, custom built muffler, and your standard blue light special equip...
My Baby: '67 GMC swb small back glass. 388ci stroker, old school bowtie heads est. 450hp, scat steele crank, eagle H beam rods, and Keith Black pistons, but only pushing 10:1 compression, fed by an Edelbrock 750 carb. THM350 trans. shiftkit w/manual valve body, 2800 stall going out back to some highway 3.42 gears, tubbed.
STD OR EXT CAB? I have an almost new set of black nerf/step bars for a EXT cab laying around in the way. If it's a long bed I have a 3" roll bar that would look good in there too after a little paint.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
well ive got roll bars off an Arkansas Game and Fish (bunny cop) truck and a brush gaurd(black). it is an ext. cab short bed. i have chrome nerf bars but i bent the hell out of one last night, how much do you want for yours? got any other goodies, lift kit ect. gotta pimp this thing out befor i ship out.
P.S. i need tires bad. 8x16x33
thanks
Daily driver: '97 Z-71 reg. cab, electric fans, dual bats, K&N cold air, custom built muffler, and your standard blue light special equip...
My Baby: '67 GMC swb small back glass. 388ci stroker, old school bowtie heads est. 450hp, scat steele crank, eagle H beam rods, and Keith Black pistons, but only pushing 10:1 compression, fed by an Edelbrock 750 carb. THM350 trans. shiftkit w/manual valve body, 2800 stall going out back to some highway 3.42 gears, tubbed.
Does it have a body lift on it yet? I have 3" blocks from a 2wd lift, should work on the 4wd body, and I have a full set of the rubber lift lips that fill the gaps in created by the body lift. I have the steering shaft extension for the body lift kit, also. Not too sure if I have all the bolts for the kit or not. I also have the front bumper relocator brackets the raise the bumper up to the body.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
hmmm. sounds interesting. it has no lift what soever.YET. i am sure i can get some bolts for it, how much you want. im a poor white boy with a 4wd.
Daily driver: '97 Z-71 reg. cab, electric fans, dual bats, K&N cold air, custom built muffler, and your standard blue light special equip...
My Baby: '67 GMC swb small back glass. 388ci stroker, old school bowtie heads est. 450hp, scat steele crank, eagle H beam rods, and Keith Black pistons, but only pushing 10:1 compression, fed by an Edelbrock 750 carb. THM350 trans. shiftkit w/manual valve body, 2800 stall going out back to some highway 3.42 gears, tubbed.
Sent P.M.
2000 RCSB Z-71 6l swap 12.8 Gone but not forgotten
2008 CCSB "tow truck" Slooowwww
1999 RCSB "WRK TRK" 4.late but getting there.
As far as the 4wd not engaging, there is a temp actuated solenoid in the front diff on that body style if I rember correct. It usually is the cause of the 4wd not engaging. Good luck
2000 RCSB Z-71 6l swap 12.8 Gone but not forgotten
2008 CCSB "tow truck" Slooowwww
1999 RCSB "WRK TRK" 4.late but getting there.
thanks i will check into it. first im going to clean the conector for the selector switch. i crawled up under the truck the other day and noticed that the switch was only half way conected and was full of mud. ill keep you posted.
Daily driver: '97 Z-71 reg. cab, electric fans, dual bats, K&N cold air, custom built muffler, and your standard blue light special equip...
My Baby: '67 GMC swb small back glass. 388ci stroker, old school bowtie heads est. 450hp, scat steele crank, eagle H beam rods, and Keith Black pistons, but only pushing 10:1 compression, fed by an Edelbrock 750 carb. THM350 trans. shiftkit w/manual valve body, 2800 stall going out back to some highway 3.42 gears, tubbed.
well i fixed the clutch and plugged my selector switch back in and it still dosent work. the front drive shaft is spinning but the tires arent getting any power. any suggestions?
thanks
Daily driver: '97 Z-71 reg. cab, electric fans, dual bats, K&N cold air, custom built muffler, and your standard blue light special equip...
My Baby: '67 GMC swb small back glass. 388ci stroker, old school bowtie heads est. 450hp, scat steele crank, eagle H beam rods, and Keith Black pistons, but only pushing 10:1 compression, fed by an Edelbrock 750 carb. THM350 trans. shiftkit w/manual valve body, 2800 stall going out back to some highway 3.42 gears, tubbed.
Did you check the thermal actuator? I also have been told on the pre 99's the wheels have to make 2.5 rotations b4 the front axle will engage. Hope this helps.
2000 RCSB Z-71 6l swap 12.8 Gone but not forgotten
2008 CCSB "tow truck" Slooowwww
1999 RCSB "WRK TRK" 4.late but getting there.
Posting Permissions
Reply With Quote
