I'm looking at a cam swap in the future for my 99 silverado. I am also considering a tune, but I'm thinking I might as well do the cam first and then have it tuned.
The comp cams XR265HR cam.... Is it a good choice? I want a cam to really give me some gains.... so am I looking at significant rear wheel gains with this cam?
Anyone have 1st person experience with this one?
Thanks,
Derek
99 White Regular Cab Sportside 5.3L
Belltech 2/4 Drop, 01 LS6 Cam and Springs, Pacesetter Headers, K&N FIPK, Cats Removed, Dynomax Ultraflow dumped before axle, K&N FIPK, Corvette Servo, Reflexxions Cowl Hood, APC Rollpan, TekStyle Tonneau, Clear Corner Lights, Polk Audio Boxed 6x9s
Popular Hot Rodding did a three cam comparison on a near stock LS1. They tested COMP cam's XR265HR, XR275HR and the XR281HR. Output was as follows.....
Stock LS1
407 HP @ 5500 rpm
375+ lbs-ft @ 4800 rpm
XR265HR
439 HP @ 6000 rpm
426 lbs-ft @ 4800 rpm
XR275HR
450 HP @ 6500 rpm
422 lbs-ft @ 5000 rpm
XR281HR
455 HP @ 6200 rpm
421 lb-ft @ 5000 rpm
All this was on a motor with no accessories, running an electric water pump, Comp cams 918 springs, AccuFab billet throttle body, Wilson billet fuel rails, Hooker long tube headers, Pro-M mass air meter and meziere electric water pump. They thought the engine needed better breathing for the 281 cam. All testing was done without changing the PCM basic programming.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
Hmmm.
Those are great results for the cam I'm looking at. I think the 265 will be the most streetable "hot cam" for me.
In the professional opinion of you engine wizzes, will the 265 cam wake up my 5.3L the same way it did the ls1?
99 White Regular Cab Sportside 5.3L
Belltech 2/4 Drop, 01 LS6 Cam and Springs, Pacesetter Headers, K&N FIPK, Cats Removed, Dynomax Ultraflow dumped before axle, K&N FIPK, Corvette Servo, Reflexxions Cowl Hood, APC Rollpan, TekStyle Tonneau, Clear Corner Lights, Polk Audio Boxed 6x9s
Their suggestion is to go with the 275 cam unless you plan on doing additional mods on an LS1. I will most likely go with the 281 since I always go overboard on everything and my truck has the LS1.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
this doesnt add up...somethings missing here i know it.Originally posted by GREG_92_C1500_2001_LS1_A4@Jul 7 2004, 03:02 PM
Stock LS1
407 HP @ 5500 rpm
375+ lbs-ft @ 4800 rpm
Hugger Orange 99 SS Hardtop #756
485rwhp/440rwtq SAE
Nothing missing. Stock internals, billet throttle body, removed hp robbing accessories, replaced hp robbing water pump with electric water pump, changed the fuel rails to a Wilson flow thru type from of all things a 5.0 mustang to keep the fuel cool, the air intake was a K&N conical filter through a straight rubber hose into the MAF instead of any twists and turns. Stock fuel injectors were used and the stock programming. Exhaust was through a pair of hooker 1-3/4" long tube headers through dual 3" flowmaster dyno mufflers. The engine they used was a crate engine Westech had in their warehouse directly from GM so nothing out of the ordinary could have been snuck into the engine to alter the test results.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
what do you guys think about an LS1 cam?
I could probobly keep the stock springs - huh?
99 White Regular Cab Sportside 5.3L
Belltech 2/4 Drop, 01 LS6 Cam and Springs, Pacesetter Headers, K&N FIPK, Cats Removed, Dynomax Ultraflow dumped before axle, K&N FIPK, Corvette Servo, Reflexxions Cowl Hood, APC Rollpan, TekStyle Tonneau, Clear Corner Lights, Polk Audio Boxed 6x9s
Posting Permissions
Reply With Quote
