Hey guys,
I need your help. I am running some American Racing Baja's they are 16x10 with a -24 offset and 4 1/2 backspacing. They look good off the truck and track up good with the M&H racemaster tires i have for them, but they look dumb installed on the truck because they stick out of the rear fenders too much. Anybody have any suggestions on a 16x10 wheel that will tuck under a little better.
Any help would be greatly appreciated.
-Brent
06 TrailBlazer SS LS2 4.10's
02 SC StepSide Factory Orange
Full Bolt-On 370 - Little Cam- Victor Jr Intake -Worked 5.3 Heads - 4.56's - Built 60E - Circle D 4000
07 CTS-V CAI, GM Performance Exhaust, Ported TB, Coil Overs
Aren't some running Bogarts? JJNLTO and maybe JamesT?
Gone, but not forgotten!
Not me. I just call mine bogarts. They are M/T wheels 16 x 12 8 lug and they are only 24 lbs. I think Bogarts get down to 15 lbs?
JJ has the real Bogarts.
Jamest
Originally Posted by SCIV
12 Sec. Club! SOLD
La Viuda negra/ a.k.a. Black Betty
LQ4 6.0L, WCCH HEADS, LEVEL 5 FLT 4L80E TRANS. WITH TRANS BREAK, YANK 3200 STALL, TRICK TURBO, TURBONETICS T-76 TURBO, CUSTOM INTERCOOLED, 68lb INJECTORS, CUSTOM S/D TUNE FROM NELSON PERFORMANCE, COMP CAM 212/214 .557/.559 116+2, SNOW METH. KIT, . ALL INSTALLED AND DYNOED AT NELSON PERFORMANCE: 5**?HP @ 5073rpms and 5**TQ @ 4389rpms AT THE WHEELS WITH 10 PSI OF BOOST. ALL 3/4 TON TRUCK 5435LBS, NOTHING TAKEN OFF, STREET TIRES, AND USUALLY 2 BABY SEATS. WANNA RIDE?
SOLD***
Do your MT's stick out? What series of wheel is it? i wonder if they make it in 6 lug????
06 TrailBlazer SS LS2 4.10's
02 SC StepSide Factory Orange
Full Bolt-On 370 - Little Cam- Victor Jr Intake -Worked 5.3 Heads - 4.56's - Built 60E - Circle D 4000
07 CTS-V CAI, GM Performance Exhaust, Ported TB, Coil Overs
Anybody else have any suggestions???
06 TrailBlazer SS LS2 4.10's
02 SC StepSide Factory Orange
Full Bolt-On 370 - Little Cam- Victor Jr Intake -Worked 5.3 Heads - 4.56's - Built 60E - Circle D 4000
07 CTS-V CAI, GM Performance Exhaust, Ported TB, Coil Overs
Get something forged. No cast wheels on performance usage plus forged wheels are so much lighter because they're thinner.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
Oh yea they stick out. I think they are 4.75 back spacing. Yes they make a six lug. I think a 16 x 10 will fit slightly over the fenderm but not much.
Mickey Thompson Performance Tires & Wheels
12 Sec. Club! SOLD
La Viuda negra/ a.k.a. Black Betty
LQ4 6.0L, WCCH HEADS, LEVEL 5 FLT 4L80E TRANS. WITH TRANS BREAK, YANK 3200 STALL, TRICK TURBO, TURBONETICS T-76 TURBO, CUSTOM INTERCOOLED, 68lb INJECTORS, CUSTOM S/D TUNE FROM NELSON PERFORMANCE, COMP CAM 212/214 .557/.559 116+2, SNOW METH. KIT, . ALL INSTALLED AND DYNOED AT NELSON PERFORMANCE: 5**?HP @ 5073rpms and 5**TQ @ 4389rpms AT THE WHEELS WITH 10 PSI OF BOOST. ALL 3/4 TON TRUCK 5435LBS, NOTHING TAKEN OFF, STREET TIRES, AND USUALLY 2 BABY SEATS. WANNA RIDE?
SOLD***
Oh yea they stick out. I think they are 4.75 back spacing. Yes they make a six lug. I think a 16 x 10 will fit slightly over the fender but not much.
Mickey Thompson Performance Tires & Wheels
Oops mine are 27 lbs, still not bad for a 3/4 ton wheel.
12 Sec. Club! SOLD
La Viuda negra/ a.k.a. Black Betty
LQ4 6.0L, WCCH HEADS, LEVEL 5 FLT 4L80E TRANS. WITH TRANS BREAK, YANK 3200 STALL, TRICK TURBO, TURBONETICS T-76 TURBO, CUSTOM INTERCOOLED, 68lb INJECTORS, CUSTOM S/D TUNE FROM NELSON PERFORMANCE, COMP CAM 212/214 .557/.559 116+2, SNOW METH. KIT, . ALL INSTALLED AND DYNOED AT NELSON PERFORMANCE: 5**?HP @ 5073rpms and 5**TQ @ 4389rpms AT THE WHEELS WITH 10 PSI OF BOOST. ALL 3/4 TON TRUCK 5435LBS, NOTHING TAKEN OFF, STREET TIRES, AND USUALLY 2 BABY SEATS. WANNA RIDE?
SOLD***
Posting Permissions
Reply With Quote