I have a 03 5.3 silverado
I had the truck programed and had the line pressure turned up but it still doesnt shift hard enough for me.
I have been looking at billet servos but not sure what to get. Will ones for a 700r4 fit the 4l60E?
Anything else I might wanna look into getting?
thanks this site has been a great help to me
get a shift kit, like trans go. corvette servos and a stall and i bet youll be happy with the trans.
Hey man i got an 05 4.8 an i just bought 3200 stall vette servo an 4thgear servo put in my truck yesterday and it makes a world of difference and i dont even have a tune yet im gettin one tomorrow at TRT but even now its bada$$ without a tune
Spend a little extra money and buy the billet servos from superior, Oregon Performance Transmission, Inc. or PATC ( 700R4, 700 Raptor Transmission from PATC, 700R4 4L60E 48RE 4L80E ) Buy a 1-2 and a 3-4 servo and you will not be disappointed. The transgo shift kit is a must in my books. You can also think about doing a Transgo 46mod vacuum shift modulator, it gets rid of the electronic transmission pressure regulator in the transmission valve body.
Last edited by RedHeartbeat; 11-10-2007 at 10:25 AM.
See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
I dont really wanna have to pull the pan yet. Will the shift kit make it shift harder? Or will just the servos do that?
Also what would a boost valve do?
Last edited by lifted98; 11-10-2007 at 12:37 PM.
the servo will help,epecially if you get a stall ,the stall softens up the best of them ,when i took my stall out it shifted like it would rattle youre teeth.with it in i couldnt even feel it shift.hope it helps .i originally did a stall and servos.go with reds suggestion,good luck
mods:2004 sierra ext sb,20s ,big brake kit w,hawk pads,air bagged,2006 6.0 lq4 swap,vortec supercharged10psi, air to water intercooled w/ dual electric fans on it ,snow meth injection kit,60lbers, e-fans ,big radiator swap ,cam 218 /222 548/550 comp .hardened prs .1.85 comp roller rockers ,guideplates ,crane double springs,trans 4l65e built .pacesetter l/ts true duals w/x pipe and magnaflows,14 bolt rearend swap ,3.73s,aroemotive fuel pump system w/elec.fuel controller and bypass regulator a/n fittings, taylor 10.5s interceptor gauge,aem w/b a/f ,autometer boost/vac NELSON 93 OCTANE TUNED .
so what will the boost valve do?
Corvette servos are fine.. I have installed a Super Hold 2nd servo once and it was Way to much ... Customer didnt like it... As Far as shift kit... Trans-go HD-2 ... Sonnex is the maker of the super hold stuff...
Originally Posted by casey23
Superior had them out first
The superior man is modest in his speech, but exceeds in his actions. - Confucius
"He who asks of life nothing but the improvement of his own nature, is less liable than anyone else to miss and waste life."- Henri Frederic Amiel
'01 Chev Z71 LT - '85 BMW 745i TURBO - '88 BMW 750iL - '88 Ford F150 XLT Lariat - '79 MB 240D - '79 MB 280S Euro
'80 MB 380SE-5.0 Euro - '85 MB 300SD - '87 MB 300SDL - 1990 MB 300SEL - '91 MB 300SE - '91 MB 560SEL
Let's face it, the red hair... makes 'em wet.
I did the vette servo...and made a huge differance.Much better 1-2 shift
Vortec Performance Tuned
LQ9 built 4L60 LTs and a billion miles on the speedo!
Posting Permissions
Reply With Quote
