+ Reply to Thread
Results 1 to 8 of 8

Thread: Cam, Rods and Springs

  1. 02-26-2006 01:18 AM #1
    JBauer
    JBauer is offline Junior Member
    Join Date
    Feb 2006
    Posts
    5
    I been wanting to do this for some time I just need to find a good shop around here that will do it for a decent price which is proving harder than I thought. The market around here is mostly ford performance for what ever reason. Any way I was wondering if anyone could give me a good idea of what type of gains I could expect from the couple things I wanna get done. Also curious if the price I will be paying is normal or can I get them for cheaper. I would go bigger on the cam but I don't plan on putting a stall in till I blow up the tranny

    5/16, high-quality seamless 4130 chromemoly, .080" wall thickness Pushrods - $154.95

    LS6 Springs - $64.95

    Comp Cams XTREME RPM XR265HR - 212/218 - .522/.529 w 1.7 rocker - 114 LSA $359.95

    Shipping $18
    http://i37.photobucket.com/albums/e6...2/1d89cfec.jpg
    Airaid CAI and MIT, Flowmaster 40 series catback, Jet 180 T-stat, TCI Billet 1-2 Servo, JBA blue plug wires, Westers 93 Hot Tune, EBC slotted frt rotors and pads, Centerline Stingray III 20s, Proxes 295/45s, Custom Paint, Plus a ton of other stuff!
    Reply With Quote Reply With Quote
  2. 02-26-2006 01:24 AM #2
    RedHeartbeat
    RedHeartbeat is offline WTH JUST HAPPENED?
    Join Date
    Nov 2003
    Location
    Denton Texas
    Posts
    20,540
    I deal with Scoggins Dickey because of their great pricing. Check out their prices at SDPC2000.com. Their LS6 spring were under $60 and their pushrods are $100 a set. Be sure to check out pricing at site sponsors TRTTurbo.com. Email them for pricing. Also TByrne.com is a site sponsor and has discount pricing at this time. Be sure to email them about LS1Truck.com discounts when asking for pricing.
    See my truck data in the "My Garage" section here... http://www.ls1truck.com/forums/my-ga...tml#post191709
    Reply With Quote Reply With Quote
  3. 02-27-2006 09:31 PM #3
    04Grill
    04Grill is offline Member
    Join Date
    Oct 2005
    Location
    Warsaw, Va
    Posts
    53
    20-35hp with the cam swap roughly is what you should see....
    04 ECSB Silverado 4X4
    Nelson Tuned - 220cam - 3000yank stall - stage 1 heads
    LS1 fans - ASP pulley - 3inch lift - ASM LT headers Mod Page
    aka 98TAauto - 98TA 11.4 @ 119 H/C street trim
    Reply With Quote Reply With Quote
  4. 02-27-2006 09:38 PM #4
    vv8
    vv8 is offline Senior Member
    Join Date
    Oct 2003
    Location
    TeXas
    Posts
    932
    why get 1.7 rockers, thats what these trucks come with stock
    http://i17.photobucket.com/albums/b9...5831PM-2-1.jpg <--- TimeSlip
    RCSB 5.3 N/A 12.31 full boltons,H/C,4.10s,3800 converter. SOLD
    04 GTO
    Both Tuned By: ME
    Reply With Quote Reply With Quote
  5. 02-28-2006 12:28 PM #5
    JBauer
    JBauer is offline Junior Member
    Join Date
    Feb 2006
    Posts
    5
    I wasn&#39;t planing on getting rockers I just copried and pasted that from somewhere and it had that in there.

    Almost every quote I have gotton so far has been &#036;1000+ for the install so I may not be doing this anytime soon.
    http://i37.photobucket.com/albums/e6...2/1d89cfec.jpg
    Airaid CAI and MIT, Flowmaster 40 series catback, Jet 180 T-stat, TCI Billet 1-2 Servo, JBA blue plug wires, Westers 93 Hot Tune, EBC slotted frt rotors and pads, Centerline Stingray III 20s, Proxes 295/45s, Custom Paint, Plus a ton of other stuff&#33;
    Reply With Quote Reply With Quote
  6. 03-01-2006 09:49 PM #6
    04Grill
    04Grill is offline Member
    Join Date
    Oct 2005
    Location
    Warsaw, Va
    Posts
    53
    damn, we only get like 200-300 for a cam install lol but i doubt you are close to Va
    04 ECSB Silverado 4X4
    Nelson Tuned - 220cam - 3000yank stall - stage 1 heads
    LS1 fans - ASP pulley - 3inch lift - ASM LT headers Mod Page
    aka 98TAauto - 98TA 11.4 @ 119 H/C street trim
    Reply With Quote Reply With Quote
  7. 03-01-2006 11:45 PM #7
    docone882000
    docone882000 is offline Senior Member
    Send a message via AIM to docone882000 Send a message via Yahoo to docone882000
    Join Date
    Jan 2006
    Location
    San Antonio
    Posts
    827
    <div class='quotetop'>QUOTE(JBauer &#064; Feb 28 2006, 11&#58;28 AM) [snapback]45625[/snapback]</div>
    I wasn&#39;t planing on getting rockers I just copried and pasted that from somewhere and it had that in there.

    Almost every quote I have gotton so far has been &#036;1000+ for the install so I may not be doing this anytime soon.
    [/b]
    Just to do that. Are they smoking crack?
    Tattoos, Kustoms, Chops, Guns and Pits..........Need I say more? AFTERLIFE KUSTOMS.

    Getting ready to put an 82 Chevy 1/2 ton blazer under the knife.

    EL JEFE
    ROUGHNECK

    Reply With Quote Reply With Quote
  8. 03-01-2006 11:56 PM #8
    vv8
    vv8 is offline Senior Member
    Join Date
    Oct 2003
    Location
    TeXas
    Posts
    932
    where ya from?? I know some one who can help ya out if your close?

    I&#39;m in the houston area sorry lol.
    http://i17.photobucket.com/albums/b9...5831PM-2-1.jpg <--- TimeSlip
    RCSB 5.3 N/A 12.31 full boltons,H/C,4.10s,3800 converter. SOLD
    04 GTO
    Both Tuned By: ME
    Reply With Quote Reply With Quote
+ Reply to Thread
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules