Major misfire problems.

[Chevydillan]

Where is the harness from or did you modify it?

[crzy8mnky]

Fuel pressure at the rail is in the right range and the injectors were just cleaned and flowed fine. However the 6 and 8 plugs were carbon fouled when pulled out. I don't know what else to test for in the fuel system. The harness is the modified 5.7 harness. Noid lights showed all 8 injectors were being pulsed and I have 12 volts on the pink wires to the injectors, along with .3 to .5 ohms on the ground wires to the computer. I even swapped in a wire directly to the computer to control the injectors with no change. The coil wiring was pulled from the harness that came with the engine. I hooked it up like lextech described in the wiring file.

One thing to note, when I turned off cylinders 4 or 7 with efi live, the truck seemed to smooth out. When I turned off any other cylinder, the truck got worse.

[Chevydillan]

Need to verify the wire locations on the computer to the injectors and coils for those cylinders. Could you post up where you have them pinned in please.

[crzy8mnky]

From lextech's file:
a Purple wire to------C2-26 for Coil #1 Control
a Red wire to---------C2-27 for coil #4 Control
a Lt.Blu/Wht wire to--C2-28 for coil #6 Control
a Dk.Grn/Wht wire to--C2-29 for coil #7 Control
a Purple/Wht wire to--C2-66 for coil #8 control
a Red/Wht wire to-----C2-67 for coil #3 control
a Dk.Grn wire to------C2-68 for coil #5 control
a Lt.Blu wire to------C2-69 for coil #2 control
a Brown wire to C2-60 for Bank #1 Coils-Low Reference
a Brn/Wht wire to C2-61 for Bank #2 Coils-Low Reference

And for the injectors, I just swapped 2/3 and 4/7. There were no problems when I had done the 0411 swap.

I've verified these multiple times. I've also pulled the plug and held it against the block and there was spark. I don't know how to tell if it's hot enough though.

[Chevydillan]

In that file 4 & 7 are backwards I believe. I checked it against 2 other files and they are switched. Try that

[crzy8mnky]

One other thing I want to throw out there. When I pulled the vacuum line off the brake booster to the intake, there was a pressure difference, and it does seem like my brakes are harder than they use to be.

[crzy8mnky]

Right now I have C1-43 for injector 7 and C1-44 for injector 4.

Edit: I think you mean for the coils, since the solid colors control the odd banks and the stripes control the even banks. The labels are wrong, but the colors match the diagrams that I have.

[Chevydillan]

Switch c2-27 and c2-29 at the PCM. That should get it running ok

[Lextech]

Right now I have C1-43 for injector 7 and C1-44 for injector 4.

Edit: I think you mean for the coils, since the solid colors control the odd banks and the stripes control the even banks. The labels are wrong, but the colors match the diagrams that I have.

I somehow had two different versions of that. One on my home laptop and one on my work laptop. I have since deleted the other version. This one "should" be correct.

11. You will be adding:
a Purple wire to-------------------C2-26 for Coil #1 Control
a Dk.Grn/Wht wire to------------C2-29 for Coil #4 Control
a Lt.Blu/Wht wire to--------------C2-28 for Coil #6 Control
a Red wire to----------------------C2-27 for Coil #7 Control
a Purple/Wht wire to------------C2-66 for Coil #8 control
a Lt.Blu wire to--------------------C2-69 for Coil #3 control
a Dk.Grn wire to------------------C2-68 for Coil #5 control
a Red/Wht wire to---------------C2-67 for Coil #2 control
a Brown wire to C2-60 for Bank #1 Coils-Low Reference
a Brn/Wht wire to C2-61 for Bank #2 Coils-Low Reference