+ Reply to Thread
Page 8 of 11 FirstFirst ... 6 7 8 9 10 ... LastLast
Results 71 to 80 of 105

Thread: Balancer Installer Tool

  1. 03-03-2011 02:12 AM #71
    screamin86's Avatar
    screamin86
    screamin86 is offline Senior Member
    Join Date
    May 2008
    Location
    verona, virgina
    Posts
    626
    Quote Originally Posted by oleshifty View Post
    first time i had mine off...no one mentioned how hard it was to get back on.... Ended up holding a 4x4 on it...and swinging a sledge at it for prolly 10 minutes until it was on far enough for the stock bolt to fit. Sure my bearings loved that.
    wow!
    03 yukon xl:intake, longtubes ory,performabuilt lvl2,circle D 278,tune, tint, lt1 fans
    92 z28: lb9 air foil vette servo magnaflow catback adjustable pan hard rod Lcas lcarbs
    86 trans am: lm7 hot cam th350 3500 stall
    Reply With Quote Reply With Quote
  2. 03-24-2011 04:20 PM #72
    dirt track racer 81
    dirt track racer 81 is offline Senior Member
    Join Date
    Jan 2008
    Posts
    252
    Bump.
    -Tyler 2000 ECSB-370-Vic Jr-FAST 4150-244/248 .612/.615 112 lsa
    Reply With Quote Reply With Quote
  3. 03-29-2011 12:29 AM #73
    DRAGGIN95's Avatar
    DRAGGIN95
    DRAGGIN95 is offline Senior Member
    Join Date
    Mar 2009
    Posts
    146
    Hello, I am ready to purchase one of these tool's, do I need to just send you the paypal, or how does this normally work? Thanks
    Reply With Quote Reply With Quote
  4. 03-29-2011 02:06 PM #74
    DRAGGIN95's Avatar
    DRAGGIN95
    DRAGGIN95 is offline Senior Member
    Join Date
    Mar 2009
    Posts
    146
    Payment sent Thanks!
    Reply With Quote Reply With Quote
  5. 03-29-2011 03:46 PM #75
    dirt track racer 81
    dirt track racer 81 is offline Senior Member
    Join Date
    Jan 2008
    Posts
    252
    Got it. Should have it sent out tomorrow.. Thanks!!
    -Tyler 2000 ECSB-370-Vic Jr-FAST 4150-244/248 .612/.615 112 lsa
    Reply With Quote Reply With Quote
  6. 05-11-2011 07:57 AM #76
    dirt track racer 81
    dirt track racer 81 is offline Senior Member
    Join Date
    Jan 2008
    Posts
    252
    Got several of these ready to go.
    Reply With Quote Reply With Quote
  7. 05-12-2011 02:20 PM #77
    armymech69
    armymech69 is offline Member
    Join Date
    Jan 2011
    Location
    Mesa, AZ
    Posts
    53
    Just sent you $$.
    05 CCSB, Volant CAI, LS2, XER281HR, stage 2 p&p with spring's, pacesetter LTs, offroad Y pipe,magnaflow muffler, 4-6 drop w/ helper bags, 20's, steel cowl hood, shaved gate, roll pan, 3000 circle D, 40k trans cooler, HIDs and someother little upgrades.
    68 Camaro, 454 BBC
    Reply With Quote Reply With Quote
  8. 05-12-2011 02:27 PM #78
    dirt track racer 81
    dirt track racer 81 is offline Senior Member
    Join Date
    Jan 2008
    Posts
    252
    Got it. I'll get the tool sent in the morning. Thanks.
    Reply With Quote Reply With Quote
  9. 05-12-2011 02:32 PM #79
    armymech69
    armymech69 is offline Member
    Join Date
    Jan 2011
    Location
    Mesa, AZ
    Posts
    53
    Thanks.
    05 CCSB, Volant CAI, LS2, XER281HR, stage 2 p&p with spring's, pacesetter LTs, offroad Y pipe,magnaflow muffler, 4-6 drop w/ helper bags, 20's, steel cowl hood, shaved gate, roll pan, 3000 circle D, 40k trans cooler, HIDs and someother little upgrades.
    68 Camaro, 454 BBC
    Reply With Quote Reply With Quote
  10. 11-18-2013 06:02 PM #80
    Duct_tape123
    Duct_tape123 is offline The Man
    Join Date
    Jan 2009
    Location
    Round Rock, Texas
    Posts
    1,699
    I know the thread is old, but do you still have any of these?
    cjriojas:if you're weather man is a 5 gallon bucket, YOUUUUUUUUUUU might be a redneck
    danger_ranger83: I see now why it cost so much to get a harness made... FML
    2boostedSilverado: I like Casey's rear end, I want to chat with him about it
    Reply With Quote Reply With Quote
+ Reply to Thread
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules