DO IT!
your small/light truck, and the lack or LOW RPM torque your 5.3L will be producing, the high stall will be great!
just be sure to get a big trans cooler, or two of them.
DO IT!
your small/light truck, and the lack or LOW RPM torque your 5.3L will be producing, the high stall will be great!
just be sure to get a big trans cooler, or two of them.
Nelson Performance
FastestTruckList.com
NP on Facebook
Youtube Channel
'94 Chevy Truck: 8.9 et, 408 twins
Well if Allen says to do it, then I'm good. That's the same thing my roommate and I were discussing. Do you think one 40000 gvw cooler will be enough?
04 RCSB 5.3, Homemade 80mm FM, TU1, TH400
I'm no expert on converters, lol, Yank and CD would be, but I've tuned and driven a ton of trucks, so I get the opportunity to feel and see what mods do and don't do.
A big stall will definitely increase performance considerably.
I run two BM coolers, the big ones with 1/2 pipe fittings and my PG (with no lockup) runs 120degs most of the time and 130degs in the city.
I know there are other good coolers out there, but the BM design cools great!
Nelson Performance
FastestTruckList.com
NP on Facebook
Youtube Channel
'94 Chevy Truck: 8.9 et, 408 twins
ok so how will a 3200 stall work in the street, say wot.. can you tell you have that connverter then, does the truck even roll with the foot off the brakes? i wish i knew someone with a big stall converter to drive there car and see how it feels and act, this is my 4th tranny lol. 20k on her so far, once she hits 40k im ripping her out and redoing it.
SORRY didnt mean to steal the thread..
Last edited by silverado00; 03-22-2011 at 04:09 PM.
2000 Chevy Silverado z71 reg cab, 5.3l procharged, dual exhaust straight piped, custom tune, 200,000 miles, 4 trannys, custom built drive shafts. two speed auto track t-case.
Well I just got off the phone with yank and the guy says it too big. Especially with the spray. He said it will get out of the hole hard but then fall on it's face after the 1/8th. He suggested a ss3600. He said I should pick up a whole second with it. So looks like I'll be saving a little longer and go with the ss3600 or a circle d 3600. I'm gonna give chris a call and see what he says
04 RCSB 5.3, Homemade 80mm FM, TU1, TH400
Chris suggested I go with his 4000 triple disk. That bad boy is $1000 lol. Idk if it's worth going with that one rather than his 3600 one for $375
04 RCSB 5.3, Homemade 80mm FM, TU1, TH400
a dyno would tell you what stall you would need
Simple: 408 on steroids!
single digits coming soon!
whats it worth? you could flip it and make a $ or save it for when you need it imo.
procharger p1sc, nelson tune, 42# marine injectors, walbro 255, lt's, ory, 4" volant cat back, PerformaBuilt level 2 pro race trans, trans. cooler with e fan, 2500 stall, aem wideband, energy bushings, spohn perf. trailing and panhard rods, mb & gear alloy 22's ( ya 2 sets, im big ballin), ss brake lines, drilled & slotted rotors, bla bla bla bla bla bla bla,
and ya it will beat a hemi.
Posting Permissions
Reply With Quote
