do your have to drop the y-pipe to take the servo out?
do your have to drop the y-pipe to take the servo out?
Blessed be the Lord my strength which teacheth my hands to war, and my fingers to fight:
Psalms 144:1
Si vis pacem, para bellum
On my 2001 2wd all I did was jack it up and change it out.
RUN WAT U BRUNG!!!!
no you just have to remove heat shield on the passenger side of the trans, i think they are 10mm bolts and then you will see the servo cover.
heres a good video for you to look at http://www.youtube.com/watch?v=4WpjGQnEixo if you dont have a new servo cover o ring DONT cut it like they say, just pull it hard and remove cover
06 silverado crew cab 4.8L
STS Kit W/turbonetics BB 60-1 .81AR T4 and intercooler 10psi
Nelson custom tune
built 4L60E-hopefully it lasts
2500 stall-Hughes converters
42LB injectors
3.5 Magnaflow exhuast
6inch lift on 35x12.50s
i had to drop the tranny crossmember... went for a two mile test drive and the cover popped out on one side blowing tranny fluid everywhere.
i didnt think there was suppose to be any fluid in there, when i pulled the cover the first time there was maybe half a cup in it. I really thought i had the snap ring fully in the grove... after the drive there is fluid from the tranny to the rear end, everywhere, and the bottom side of the cover is out further than the top. I knew the servo wouldnt be as easy as it said. it also wont go in 4th...
Blessed be the Lord my strength which teacheth my hands to war, and my fingers to fight:
Psalms 144:1
Si vis pacem, para bellum
yes that snap ring has to be seated all the way in, i used a pry bar and wedged it between the servo cover and body and pushed it down. before you re-install the servo make sure ALL the orings on the servos are good, also check the split orings on the 2nd and 4th piston to make sure there not bad. There is soppose to be fluid in it as well. not much but like you said a cup or so.
06 silverado crew cab 4.8L
STS Kit W/turbonetics BB 60-1 .81AR T4 and intercooler 10psi
Nelson custom tune
built 4L60E-hopefully it lasts
2500 stall-Hughes converters
42LB injectors
3.5 Magnaflow exhuast
6inch lift on 35x12.50s
well, when the cover got pushed out, it went out on the top but the bottom side actually trapped the snap ring in the groove. so after two hours of fighting snap ring then the cover, its off. 4th apply piston (i think thats what its called) came right off. but the pin and assembly wont pull out, easily. its dark again, and i have plans, so i get home at 545pm tomorrow and its getting dark around 530, so idk when i'll be able to get at it again...
I can change 4 struts and springs in a hour and 15 minutes from jack up to jack down, when doing it for the first time, but a "30 minute" servo install has taken me this long... I feel like the kid who took a year to swap rearends.
Blessed be the Lord my strength which teacheth my hands to war, and my fingers to fight:
Psalms 144:1
Si vis pacem, para bellum
Originally Posted by kyhunter89
That's an epic comment. Sorry for your issues.
1969 Chevy RCLB C10 350/TH400 SOLD
2007 Chevy RCSB 4.8 4x4 LS SOLD
2008 Chevy RCSB 5.3 4x4 LT SOLD
2010 Chevy CCSB 6.2 4x4 LT SOLD
2005 GMC CCLB DRW 6.6 Duramax 4x4 191,000 and counting
2013 FORD CCSB F350 6.7 Powerstroke 4x4
Posting Permissions
Reply With Quote
