+ Reply to Thread
Results 1 to 7 of 7

Thread: floor coating

  1. 11-06-2008 11:30 PM #1
    z71xl
    z71xl is offline Member
    Join Date
    Aug 2006
    Posts
    33

    floor coating

    was just wondering what you guys use for a floor paint or sealer on your garage or shop floors? I waork out of my garage every night for some side cash to help offset the wants disease i have and am getting sick of cleaning the garage everynight! The garage itself doesn't get that bad its just the cement dust from sweeping every night gets everything else dirty. What do you guys use or suggest? I dont mind spending decent money if it will hold up and wont have to be redone every couple years! I'm constantly pulling cars in and out, dragging jacks and stands around so I need something thats tough. Any insight would be greatly appreciated!
    Reply With Quote Reply With Quote
  2. 11-06-2008 11:35 PM #2
    txarkitekt's Avatar
    txarkitekt
    txarkitekt is offline Resident Smart Ass™
    Join Date
    Feb 2007
    Location
    Fort Worth
    Posts
    9,578
    ArmorProxy FTW.

    Here ya go...

    2000 ECSB 6.0L
    TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
    Reply With Quote Reply With Quote
  3. 11-07-2008 12:03 PM #3
    Wildman's Avatar
    Wildman
    Wildman is offline Stubborn...Enough Said!
    Send a message via MSN to Wildman
    Join Date
    Oct 2008
    Location
    Killeen, TX
    Posts
    170
    I have custom stained concrete in the garage. (Stained with oil and stained with burnout marks) I have heard some use concrete sealers with waterproofers. These look like better options!
    Last edited by Wildman; 11-07-2008 at 12:09 PM.


    2007 Chevy Silverado Classic 4.3L V6
    Magnaflow Muffler, CFM Technologies CNC Machined High Flow Vortec Throttle Blades, STS Rear Turbo, Intercooler, Accell Distributor and Coil, 8mm wire, Autolite Platinum plugs, Runs out of fuel at 4000RPM. Marine intake with larger injectors soon. Hoping to squeeze 10psi.
    Reply With Quote Reply With Quote
  4. 11-07-2008 05:54 PM #4
    Ramsey
    Ramsey is offline Senior Member
    Join Date
    Jun 2007
    Location
    saratoga springs ,new york {upstate ,adirondacks }
    Posts
    1,878
    use a 2 part epoxy with about a 1/2 hour pot life ,so move quickly.lol.dont use the latex epoxy that home depot sells,itll peel right up
    mods:2004 sierra ext sb,20s ,big brake kit w,hawk pads,air bagged,2006 6.0 lq4 swap,vortec supercharged10psi, air to water intercooled w/ dual electric fans on it ,snow meth injection kit,60lbers, e-fans ,big radiator swap ,cam 218 /222 548/550 comp .hardened prs .1.85 comp roller rockers ,guideplates ,crane double springs,trans 4l65e built .pacesetter l/ts true duals w/x pipe and magnaflows,14 bolt rearend swap ,3.73s,aroemotive fuel pump system w/elec.fuel controller and bypass regulator a/n fittings, taylor 10.5s interceptor gauge,aem w/b a/f ,autometer boost/vac NELSON 93 OCTANE TUNED .
    Reply With Quote Reply With Quote
  5. 11-07-2008 06:00 PM #5
    foggy's Avatar
    foggy
    foggy is offline Senior Member
    Join Date
    Aug 2005
    Location
    St. Anthony, Indiana
    Posts
    1,592
    I used this in my shop UCoat It Do-it Yourself Floor Coatings for a Durable, Protective Finish

    burnout track video
    Reply With Quote Reply With Quote
  6. 11-07-2008 06:05 PM #6
    Ramsey
    Ramsey is offline Senior Member
    Join Date
    Jun 2007
    Location
    saratoga springs ,new york {upstate ,adirondacks }
    Posts
    1,878
    yup that will do.its a catalysed epoxy,thats what your looking for,trust me ive been painting for 25 years.
    mods:2004 sierra ext sb,20s ,big brake kit w,hawk pads,air bagged,2006 6.0 lq4 swap,vortec supercharged10psi, air to water intercooled w/ dual electric fans on it ,snow meth injection kit,60lbers, e-fans ,big radiator swap ,cam 218 /222 548/550 comp .hardened prs .1.85 comp roller rockers ,guideplates ,crane double springs,trans 4l65e built .pacesetter l/ts true duals w/x pipe and magnaflows,14 bolt rearend swap ,3.73s,aroemotive fuel pump system w/elec.fuel controller and bypass regulator a/n fittings, taylor 10.5s interceptor gauge,aem w/b a/f ,autometer boost/vac NELSON 93 OCTANE TUNED .
    Reply With Quote Reply With Quote
  7. 11-07-2008 06:08 PM #7
    Ramsey
    Ramsey is offline Senior Member
    Join Date
    Jun 2007
    Location
    saratoga springs ,new york {upstate ,adirondacks }
    Posts
    1,878
    Quote Originally Posted by txarkitekt View Post
    ArmorProxy FTW.

    Here ya go...
    ive seen the sprinkle come right out of te finish.
    mods:2004 sierra ext sb,20s ,big brake kit w,hawk pads,air bagged,2006 6.0 lq4 swap,vortec supercharged10psi, air to water intercooled w/ dual electric fans on it ,snow meth injection kit,60lbers, e-fans ,big radiator swap ,cam 218 /222 548/550 comp .hardened prs .1.85 comp roller rockers ,guideplates ,crane double springs,trans 4l65e built .pacesetter l/ts true duals w/x pipe and magnaflows,14 bolt rearend swap ,3.73s,aroemotive fuel pump system w/elec.fuel controller and bypass regulator a/n fittings, taylor 10.5s interceptor gauge,aem w/b a/f ,autometer boost/vac NELSON 93 OCTANE TUNED .
    Reply With Quote Reply With Quote
+ Reply to Thread
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules