What brand of headers will give the best overall results?
What brand of headers will give the best overall results?
if you have a 2wd check out the pacesetter LT's. you can see a pic of them in my cardomain in my sig. if 4wd look into the asm's.
old mod list: H/C/I/N/E/G 408
new mod list: 5.3, gears/posi, mufler and tune : (
ASM Long Tubes are great headers. They have a great fit and finish. They are a lil more expensive than Pacesetter's though. my second choice would have been Pacesetter's no doubt.
2002 Red Chevy RCSS (engine mods)- 05 5.3L, Procharger P-1SC 9lb.pulley, 80mm BBK TB, TB By-Pass, 38lb. Inj., AlkyControl Meth Kit, ASM L/T's, Magnaflow X-pipe, Borla's, FLT Level 5 4L65e, PI 3000 Stall, B&M Tranny Cooler, 3:73's, G-80, E-Fans, 160' Thermo. Custom Built Intake with K&N. WideBand 02 Sensor, DIXIE TUNED.
wheres a cheap place to get the pacesetters?? cheapest i have found is about $400
sprayedenali: i like catching, but not fishingOriginally Posted by DamnYankee
lol...I wish you would never paint your truck...I bet it bugs them that much more that a primered up truck just soggied his Wheaties. good job buddy
DBTBSS: bring Tyler... we need someone to make fun of
MidnightRider: your right im gay
DamnYankee: my nana failed
DamnYankee: confused...if it can't keep up to begin with, how can it keep up
mitch cobb racing: ya, allen played with it for a while, HUGE difference
How do ASM and Pacesetter compare with The Other Guys headers?
2002 Chevy Silverado Z71
Alpine DVA-7996, PXA-H700, KCA-420i
Audison LRx 1x400 and 3 1x250
Focal Beryllium Tweeters and 8" Sub, Focal Utopia 7" Midrange, 2x Focal Access 40A 16" Sub
K&N Air Filter, Flowmaster Exhaust, Hypertech Programmer III, 20" Boss 309 on Nitto Mud Grappler 33x12.50R20
other guys(togs) are top notch also...
i have asm's and love them so far! Togs, ASM's, thorleys, dynamax, and SS works are the only ones that fit 4x4's
04 ECSB Silverado 4X4
Nelson Tuned - 220cam - 3000yank stall - stage 1 heads
LS1 fans - ASP pulley - 3inch lift - ASM LT headers Mod Page
aka 98TAauto - 98TA 11.4 @ 119 H/C street trim
Dynatech also works for 4X4. I have them and they are fine.
dynatechs are sweet.. but 1200bucks?
04 ECSB Silverado 4X4
Nelson Tuned - 220cam - 3000yank stall - stage 1 heads
LS1 fans - ASP pulley - 3inch lift - ASM LT headers Mod Page
aka 98TAauto - 98TA 11.4 @ 119 H/C street trim
Stainless steel and with 2 higher flow cats that come with dynatech. Fits decently. Why wouldn't they cost more?Originally posted by 04Grill@Nov 12 2005, 07:30 PM
dynatechs are sweet.. but 1200bucks?
I second this. I spent the money for Dynatech, I don't regret the purchase one bit.Originally posted by aklim+Nov 13 2005, 10:54 PM--><div class='quotetop'>QUOTE(aklim @ Nov 13 2005, 10:54 PM)</div><!--QuoteBegin-04GrillStainless steel and with 2 higher flow cats that come with dynatech. Fits decently. Why wouldn't they cost more? [/b]@Nov 12 2005, 07:30 PM
dynatechs are sweet.. but 1200bucks?
2000 Silverado ECSB, 5.3L, 7" CST/3" PA lift, Hanneman 'glass fenders & bedsides, Currie Dana 60 W/ Detroit Locker, 4.56:1 gears , Willwood Dynalite Pro 4 piston rear brakes, Bowtie Overdrives 4L80E, Nelson Tune & Fan Harness, Harland-Sharp 1.8 Roller Rockers, 2200RPM Converter, Mezerie electric water pump, K&N FIPK II, Dynatech Supermaxx SS LT headers & SS cats, Flowmaster American Thunder cat back, Magnecor wires, Flex-a-lite 282 monster fans, B&M Hi-Tek trans cooler . No DEathCOOL.
And an ls1.com decal on the back window!
Posting Permissions
Reply With Quote
