Anyone made their own subwoofer box thats goes under the back seat of an extended cab truck? I got two tens and wanna make the box that holds the subs facing down. Any body got any measurements of their box?
Anyone made their own subwoofer box thats goes under the back seat of an extended cab truck? I got two tens and wanna make the box that holds the subs facing down. Any body got any measurements of their box?
2008 GMC Sierra SLE....370ci LY6 with some goodiesSOLD
1995 C2500- LS1 swap with a mp112
build thread- http://www.ls1truck.com/forums/lsx-t...-ls1-swap.html
Yep, I've got several designs that I have built.
cjriojas:if you're weather man is a 5 gallon bucket, YOUUUUUUUUUUU might be a redneck
danger_ranger83: I see now why it cost so much to get a harness made... FML
2boostedSilverado: I like Casey's rear end, I want to chat with him about it
Dang nice Duct_tape123!
2013 EC Silverado aka redruM (Just a couple bolt ons.)
2007 RC Silverado aka ?
1998 Trans AM aka Red Dragon
"Your pull your truck to the track on a trailer, I race you with a truck that pulled a trailer to the track."
Hey Duct_tape123 would you recommend using shallow mount woofers with that box?
RUN WAT U BRUNG!!!!
I've got a pair of Rockford Fosgate P3s in the upper box. 1.73 cubic feet with just over 5.75" mounting depth. If the sub doesn't have a wide magnet you could squeeze a 6"+ sub in there. The lower box is 1.23 cubic feet with the same mounting depth but it has a 'recessed' area for my Rockford Fosgate Power1000 5 channel amp. If you can run a full depth sub, do it. You will be much happier with the output.
And thanks for the kind words, guys.
cjriojas:if you're weather man is a 5 gallon bucket, YOUUUUUUUUUUU might be a redneck
danger_ranger83: I see now why it cost so much to get a harness made... FML
2boostedSilverado: I like Casey's rear end, I want to chat with him about it
NICE!!! thats exactly what i was looking for thank ya
2008 GMC Sierra SLE....370ci LY6 with some goodies
1995 C2500- LS1 swap with a mp112
build thread- http://www.ls1truck.com/forums/lsx-t...-ls1-swap.html
Will this fit without modifying the back seat? How much lift on the seat is needed?Originally Posted by Duct_tape123
Yep, I've got several designs that I have built.
Also I plan to cut that design by 1/3 and run one ten.
This one......
http://http://www.audioque.com/Stree...ofer_p_10.html
Last edited by kerrige; 06-11-2012 at 04:51 PM.
ECSB 2kSierra 2wd 4.8L-K&N-HPtuners-Calspeed LT's-Magnaflow-Tahoe20's-HankookRH06
waiting to go in... 3.90s, 214/220cam
This box fits all ext cab trucks up to the (99-07 classic)NNBS AFAIK. Yes, it fits without lifting back seat. I just built a single 10" ported for my RE SE10 and it slams. You want to go sealed or ported?
EDIT : link FAIL
Last edited by Duct_tape123; 06-12-2012 at 10:08 PM.
cjriojas:if you're weather man is a 5 gallon bucket, YOUUUUUUUUUUU might be a redneck
danger_ranger83: I see now why it cost so much to get a harness made... FML
2boostedSilverado: I like Casey's rear end, I want to chat with him about it
Box I built for my old truck was dang near exact same dimensions as the first plan you have. Only difference that I can see is that I cut off the bottom 2" in the front. It ended up letting the sound travel better.
That don't look like mine?!?!?
Posting Permissions
Reply With Quote
