Turbo 4.8L questions

[slowls1z28]

Ok, I dont have a truck but since this motor comes in the trucks I figure this is the best site to get the info I am after. First off the car is a 92 Z28 that I swapped a LS1 into and have recently pulled the motor to go another route. I have a 4.8L and am going to turbo it but I want to keep it as "sleeper" as possible unlike it was before with the cammed LS1. I was thinking after doing some research looking at a few other 4.8L turbo builds of going with a LS6 cam, 241 heads (since I already have those off my LS1) to drop comp. and my LS6 intake. Then I will build a kit using truck manifolds and my question is which turbo to go with, the car has a fully built RMVB with a brake and will have around a 3K or so stall once its restalled. The car is LIGHT as with the LS1 in it weighed around 2900lb raceweight. The only plans to do anything to the 4.8 is a simple rebuild with rod bolts then later down the road when I get the extra money I will build my LS1 to handle boost or go with a 370 6L. Any help would be greatly appreciated!

Thanks, Nick!

[jetmech]

You've explained your plans but what exactly are you asking? I'm running a turbo'd 4.8L and I think I can help but I'm not sure what information you're after.

[slowls1z28]

Sorry, my question was in the middle of all that guess I should have proof read better before posting. I mainly want to know which turbo would be a good turbo, I would like one that can make good power but not lag like crazy and have a useless short powerband. I'm kinda new in the turbo field so I dont want to waste money buying one thats doesnt work properly. I guess a reasonable power goal would be 550-600hp if that helps. And also what kind of boost levels can these motors handle safetly?

[jetmech]

In that case I'd say run about a 70mm. It'll spool pretty quick and you'll be able to squeeze about 600 out of it with a good tune and low enough IAT's. If you're new to turbos, then you may want to research a bit more before taking the plunge because there are a lot of "little things" that need attention. I can fill you in on a lot of it if you'd like - I've learned a lot since I first went the turbo route. These engines can handle more boost than you might think. I've ran 14psi a number of times with no problems and the only reason I didn't turn the boost controller up further, is because I'm still running the stock 1 bar MAP and I doubt my injectors can support more than 14psi.....even with both meth nozzles. An LS6 cam is a good boost cam though.

[slowls1z28]

Thanks for the info. Thats around what size I was leaning towards so I am on the right track. As far as the little things, I know fuel system if the most important thing to keep the motor safe so that'll be taken care of with twin 255's in tank. I'm pretty sure the stock fuel lines can handle that much power without a issue as its a 3/8 supply line if I recall right. I know there are other things I am either overlooking or forgetting right now but I wont even be starting the turbo side of the build untill I get most of the parts I need and get the fuel system taken care of. Which will be a few months away once It cools down around here since welding in 110* heat index sucks! If you can help with anything or see anything I may be looking at wrong please let me know, I would rather know first hand then learn the hard way!

[slowls1z28]

Oh, and as far as tuning and any other things I may need I have Allan at Futral right down the road who takes care of all that for me so tune will be good. I just dont like bothering him while he's working making him a living with my little questions that someone can easily answer on there free time. I'd say if I can get that 600hp out of this setup I will be happy since that'll be faster than the LS1 was NA so that sounds good! BTW what is the record in the 1/4 for a 4.8 anyways?

[00chevylade]

You've explained your plans but what exactly are you asking? I'm running a turbo'd 4.8L and I think I can help but I'm not sure what information you're after.

what heads will work on my 4.8l so I could boost it?