I'm about to buy an Eaton Posi to put in and wanted to make sure I bought the correct one. Is this it:eBay Motors: EATON POSI 10 BOLT 8.5 GM CHEVY GMC CAR TRUCK SBC SB 4x (item 110163222783 end time Sep-06-07 19:00:00 PDT)
This should go well with my ET Streets!!
2004 Silverado Crew Cab, forged iron 5.7, STS w/MP turbo, 10+ psi, FMIC, Tial 50mm BOV, Vic Jr, Snow performance meth, MTI Stealth cam .220/.220 .581/.581 115lsa, Comp chromoly pushrods, Yank TT3000 stall, LS1 Efans, 160 tstat, Trucool 40k trans cooler, 60# injectors, Walbro fuel pump, Patriot springs, Built 4l65E w/billet input & output shafts, Eaton posi, SD tuned...all installed by Klein North Automotive
Thats wierd, it lists the 30 spline part number, but when it says it "fits the following" it doesnt list your year of truck.. You might want to check up on that by calling, just to make sure.
1951 3100
1984 C10
Yours will be the 30 spline, but call to make sure that they have the EXACT one...
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
I confirmed that they have the exact one, but the guy said that I might need a bearing kit. Should I get this or is it ok to reuse? Keep in mind, I'd rather spend a little now as opposed to a lot later!Originally Posted by txarkitekt
2004 Silverado Crew Cab, forged iron 5.7, STS w/MP turbo, 10+ psi, FMIC, Tial 50mm BOV, Vic Jr, Snow performance meth, MTI Stealth cam .220/.220 .581/.581 115lsa, Comp chromoly pushrods, Yank TT3000 stall, LS1 Efans, 160 tstat, Trucool 40k trans cooler, 60# injectors, Walbro fuel pump, Patriot springs, Built 4l65E w/billet input & output shafts, Eaton posi, SD tuned...all installed by Klein North Automotive
Well, how many miles? How much abuse has it taken? Depending on those factors, you make the call, but I do like your way of thinking---"I'd rather spend a little now as opposed to a lot later!" If you had really, really low miles amd drove like my grandmother, then I'd say keep them. But I'd go ahead and get the new bearings...IMO...
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
That's what I figured! Better safe than sorry! I've got a little over 70k on it right now and it's been driven not hard but definitely not like a grandma. Thanks for the input!
2004 Silverado Crew Cab, forged iron 5.7, STS w/MP turbo, 10+ psi, FMIC, Tial 50mm BOV, Vic Jr, Snow performance meth, MTI Stealth cam .220/.220 .581/.581 115lsa, Comp chromoly pushrods, Yank TT3000 stall, LS1 Efans, 160 tstat, Trucool 40k trans cooler, 60# injectors, Walbro fuel pump, Patriot springs, Built 4l65E w/billet input & output shafts, Eaton posi, SD tuned...all installed by Klein North Automotive
Posting Permissions
Reply With Quote
