i have recently purchased a wideband gauge and sensor... in the instructions it says to mount the sensor before the cat(s) for a more accurated reading... but i only have one sensor, and i have 2 cats before the Y. Please help... do i only run one sensor comming from one exhaust mannifold, or do i put the sensor after the Y, Which would be after the cats, but it would get both exhaust manifolds??? PLEASE HELP...
05 Silverado RCSB...
LQ9, TVS 1900, 4L80e, & EFI live.
07 Silverado VortecMAX CCSB LTZ Z-71...
Stock... so far
08 Cadillac Escalade 6.2 / 6.0... Wife wagon
Insstall it were the 2 pipes merge together.
mods:2004 sierra ext sb,20s ,big brake kit w,hawk pads,air bagged,2006 6.0 lq4 swap,vortec supercharged10psi, air to water intercooled w/ dual electric fans on it ,snow meth injection kit,60lbers, e-fans ,big radiator swap ,cam 218 /222 548/550 comp .hardened prs .1.85 comp roller rockers ,guideplates ,crane double springs,trans 4l65e built .pacesetter l/ts true duals w/x pipe and magnaflows,14 bolt rearend swap ,3.73s,aroemotive fuel pump system w/elec.fuel controller and bypass regulator a/n fittings, taylor 10.5s interceptor gauge,aem w/b a/f ,autometer boost/vac NELSON 93 OCTANE TUNED .
even if its after the cats??? it says in the installation instructions that it is more accurate before the cat(s)...
05 Silverado RCSB...
LQ9, TVS 1900, 4L80e, & EFI live.
07 Silverado VortecMAX CCSB LTZ Z-71...
Stock... so far
08 Cadillac Escalade 6.2 / 6.0... Wife wagon
when i had my stock y pipe on ,allen nelson had me install mine were the 2 pipes merge.i believe i had the 2 cats coming off each manifold b4 the merge ,then i had another after the merge further downstream.it worked fine.
mods:2004 sierra ext sb,20s ,big brake kit w,hawk pads,air bagged,2006 6.0 lq4 swap,vortec supercharged10psi, air to water intercooled w/ dual electric fans on it ,snow meth injection kit,60lbers, e-fans ,big radiator swap ,cam 218 /222 548/550 comp .hardened prs .1.85 comp roller rockers ,guideplates ,crane double springs,trans 4l65e built .pacesetter l/ts true duals w/x pipe and magnaflows,14 bolt rearend swap ,3.73s,aroemotive fuel pump system w/elec.fuel controller and bypass regulator a/n fittings, taylor 10.5s interceptor gauge,aem w/b a/f ,autometer boost/vac NELSON 93 OCTANE TUNED .
it's gonna read pretty much the same in any location.
I know, I have about 1000 bungs on my exhaust lol, they all read the same.
Nelson Performance
FastestTruckList.com
NP on Facebook
Youtube Channel
'94 Chevy Truck: 8.9 et, 408 twins
ive been hearing alot that i need to put it between the exhasut manifiold and the cat on the drivers side...
05 Silverado RCSB...
LQ9, TVS 1900, 4L80e, & EFI live.
07 Silverado VortecMAX CCSB LTZ Z-71...
Stock... so far
08 Cadillac Escalade 6.2 / 6.0... Wife wagon
If you put it before the cat it's the same on either side. There is no difference between left and right. Allen knows better than me if after the Y is OK so I'll leave that up to you.
they just sadi because the #7 cylinder goes lean first... its more accurate on the drivers side.
05 Silverado RCSB...
LQ9, TVS 1900, 4L80e, & EFI live.
07 Silverado VortecMAX CCSB LTZ Z-71...
Stock... so far
08 Cadillac Escalade 6.2 / 6.0... Wife wagon
Posting Permissions
Reply With Quote
