All LS Based Conversions
Starting this to answer as many questions as I can in one place. I am trying to compile the most complete list of what to do to complete a conversion...
Hey Guys, these questions get asked quite a bit, and what better way than to make a sticky with all the part numbers you'll need. I'm open to...
2001 silverado (Thanks Banker099) This image has been resized. Click this bar to view the full image. The original image is sized 799x247...
ive got a 98 f-body ls1 with a street and performance wiring harness. Just wondering if I can even start the engine without having the computer...
Well, I was gettin in to the nitty gritty of things today and ran into a problem. I removed the bed and about 6 inches back from the cab, the frame...
91 silverado, 2001 5.3, 95 dash.(no airbag in it, has cupholders) I took the underhood junction box from the 2001 and have it on my fenderwell....
I am trying to find the cheapest but easiest route to my power goals. I can buy a used cheap 5.3 with high miles and swap the shortblock out with a...
I know I've talked a little to Ron on this board about his M5 to M6 swap, but has anyone swapped an A4-M6 in the NBS trucks? My main questions are:...
alright, Ive done alot of searching and found a lot of good info but not quite what i was looking for. I found a 6.0,4l80e,t-case, wiring...
If I go with a computer from an LS1 for my 5.3, can I use one that was for a 6 speed car and have it programmed? As of now, the only computer I have...
Hey folks! I've been exploring online casinos for a while now but still feel like I’m not getting the most out of my experience. How do you maximize...
On the 5.3 starter there are 3 posts on the starter. With engine in truck. The biggest post closest to frame goes to battery hot. The small post...
Couple of questions? 1) the vapor purge valve on front of intake can we get rid of this or is it something needed? If I do keep it does it tie in...
I'm new here and i'm doin a conversion useing a 2003 5.3 and 4l60e . My question is now that i have removed the un needed wires from the harness i...
I am swapping a 4.3 in a 2006 silverado 1500, to a 6.0 LQ4 from a 2002 2500 I have engine, fuse box, pcm, and harness from the 2500, am I better to...
I'm going to post what I did to mate my nv3500 to my 5.3 since I wasn't able to find any reliable info when I did my swap. I bought the flywheel from...
Hello all, I completed an 8.1L swap last year in a 70’s GM truck using a MEFI-4 ECM. Never got that damn thing tuned right so I just replaced ...
Hello. New member here. I finally brought home my 5.3 & 4L60E in my minivan since my truck's 4-banger is knocking. The 2nd 4L60 is for my buddy....
Hi Everyone. Swapped a 5.3 from a 2002 Tahoe into our 97 2 door Tahoe. We have been driving the thing all over the place because it is so much fun...
1988 k2500 5.7 recently started knocking. So what I wanted to know would it be more sufficient to put another 5.7 in it? Or I have a 4.8 and do a...
So, I just want to put this out there before anyone else gets screwed over by this *******. Johns custom wiring 475 E South Airport Rd Traverse...
I just finished making an A/C bracket kit that will allow the stock A/C compressor and lines to be used when doing a Gen3 install. I have seen a lot...
I have been searching for what I need for a year and no one makes it. (that I can find) The closest Ive seen is LSX innovations one thats for an LT...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
