+ Reply to Thread
Results 1 to 10 of 13

Thread: my 5.3 swap into my 37 chevy truck

Hybrid View

  1. #1
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106

    my 5.3 swap into my 37 chevy truck







    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  2. #2
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    13903412_10154364792136684_2455720104770709193_n by joa kwin, on Flickr

    the frame next to my mini

    The 37’s y-pipe by joa kwin, on Flickr

    y-pipe I built for the 5.3. it crosses over behind the trans

    57034693_392993441482429_9053709704697479168_n by joa kwin, on Flickr

    5.3 with 4l80e
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  3. #3
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  4. #4
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    56173163_1013720098833201_4886948286289674240_n by joa kwin, on Flickr

    4l80e is out of a 04 3500 Silverado with gas engine, had 55k miles on it,
    so I replaced the filter and the input and out seals and pan seal
    got the trans for $500
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  5. #5
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    56252802_2591001554304775_6473227520001966080_n by joa kwin, on Flickr

    right side valve cover off
    I got the motor in dec 2008, and it sat sealed up since, ones a year I put alittle oil in the cylinders

    motor had 50k miles on it when I got it
    its from a 2001 or 2002 gmc Yukon, dbw,

    the suv was rolled

    55485950_312999799361362_6899397062991806464_n by joa kwin, on Flickr

    I got a ls3 oil pan, 8 qt monster, its not as deep as the truck pan
    so I was able to sit the motor alittle deeper into the frame, to lower the weight, and I mounted the engine 14 inches to the rear
    paid $100 for the new take off ls3 pan and pick up and dip stick tube and stick

    56656192_395297117721176_1710811376668114944_n by joa kwin, on Flickr
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  6. #6
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    57161034_364175004308528_3851587020191170560_n by joa kwin, on Flickr

    my dad gave me this 80's suburban fuel tank, It was new and free so im going with it
    ordered a tbi fuel sender from a 87, and then changed the pump to the high psi pump that's made for the pressure needed for the swap

    57561072_1001290390060324_3094210812177285120_n by joa kwin, on Flickr

    the muffler I plan to go with, haven't mounted it yet but im close to it now
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  7. #7
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    59138273_2270656153148939_6489626546951684096_n by joa kwin, on Flickr
    caliper im going with for the front brakes

    Untitled by joa kwin, on Flickr
    my mini cooper when I got done painting the body after I made the wide body fenders
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  8. #8
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    Untitled by joa kwin, on Flickr

    z06 caliper onto belltech s10 blazer spindle with wooden mock up bracket

    vette brakes on the 37 by joa kwin, on Flickr

    I found some non drilled and slotted rotors for the z06 on rockauto, and they were like 50 bucks each, I have some drilled and slotted rotors for it but I didn't want to mess them up during the build or whatever
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  9. #9
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    video-1582921347 by joa kwin, on Flickr

    in this video, I primed the oil system and put a regular oil gauge and turned the key just to build up oil and make sure it would build up oil pressure, also I didn't have spark plugs in the motor because I was using the battery from my mini aka super small battery

    I replaced a lot seals on the motor,
    oil pan, front/rear mains, timing cover seal, intake manifold seals, valve covers, valley seal
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

  10. #10
    Join Date
    Nov 2003
    Location
    england uk/San Diego
    Posts
    106
    the 37 start up by joa kwin, on Flickr


    here I started it up

    and I was getting oil coming out of the exhaust

    so I knew I had to do valve seals
    new project
    37 m-series 3/4 ton chevy truck,
    plans: 5.3/4l80e, cut down ford 9 inch, 6piston brakes

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts