+ Reply to Thread
Results 1 to 7 of 7

Thread: thinking bout making my own stand alone harness but have questions??

  1. 03-04-2012 03:52 PM #1
    S!nC!tyHeavyChevy
    S!nC!tyHeavyChevy is offline Junior Member
    Join Date
    Nov 2011
    Location
    Las Vegas
    Posts
    10

    thinking bout making my own stand alone harness but have questions??

    ok iv been looking around at harness for my dbc 5.3 but have also looked at the pin outs at lt1swap.com. now i need to retain all smog equipment and will be running a manual trans so i can delete the trans wiring. i understand all sensors 12v positive have to hook up to a 12v accessory controlled by the ignition and that i need to run the two 12v constants off the harness to the ignition. Now heres my question i will be running alot of accessories in this truck so i would like to retain the fuse block off the 5.3 harness, can i wire the 12v constants from the fuse block and the accessories positive from the fuse block to the ignition like the factory would or is it more complicated then that?
    when they run my plates model and make
    I'ma shake like I'm riding with a K
    Pedal to the medal rarely hit the brake
    Reply With Quote Reply With Quote
  2. 03-04-2012 04:59 PM #2
    myzterray's Avatar
    myzterray
    myzterray is offline 17 Second Truck Club
    Join Date
    Sep 2011
    Location
    Atlanta Ga
    Posts
    692
    Quote Originally Posted by S!nC!tyHeavyChevy View Post
    ok iv been looking around at harness for my dbc 5.3 but have also looked at the pin outs at lt1swap.com. now i need to retain all smog equipment and will be running a manual trans so i can delete the trans wiring. i understand all sensors 12v positive have to hook up to a 12v accessory controlled by the ignition and that i need to run the two 12v constants off the harness to the ignition. Now heres my question i will be running alot of accessories in this truck so i would like to retain the fuse block off the 5.3 harness, can i wire the 12v constants from the fuse block and the accessories positive from the fuse block to the ignition like the factory would or is it more complicated then that?
    i did my own harness using the lt1swap.com website. what are you putting the engine into? also i see your in las vegas..i just moved here few weeks ago good to know someone else out here is doing a swap.
    96 2 Door Tahoe 4wd / 5.3 Swap / CAI / Tune / Pacesetter LTs / Magnaflow / LED Dash / Novak A/C Bracket /


    http://www.ls1truck.com/forums/lsx-t...ders-pics.html
    Reply With Quote Reply With Quote
  3. 03-04-2012 06:00 PM #3
    Bowtyrel
    Bowtyrel is offline Member
    Join Date
    Jun 2011
    Posts
    55
    Quote Originally Posted by myzterray View Post
    i did my own harness using the lt1swap.com website. what are you putting the engine into? also i see your in las vegas..i just moved here few weeks ago good to know someone else out here is doing a swap.
    Yea good to know there are more ppl in Nevada on here
    Reply With Quote Reply With Quote
  4. 03-04-2012 06:08 PM #4
    myzterray's Avatar
    myzterray
    myzterray is offline 17 Second Truck Club
    Join Date
    Sep 2011
    Location
    Atlanta Ga
    Posts
    692
    Quote Originally Posted by Bowtyrel View Post
    Yea good to know there are more ppl in Nevada on here
    Where are you located?
    Reply With Quote Reply With Quote
  5. 03-04-2012 08:02 PM #5
    Bowtyrel
    Bowtyrel is offline Member
    Join Date
    Jun 2011
    Posts
    55
    Elko, northeast corner
    Reply With Quote Reply With Quote
  6. 03-04-2012 08:19 PM #6
    myzterray's Avatar
    myzterray
    myzterray is offline 17 Second Truck Club
    Join Date
    Sep 2011
    Location
    Atlanta Ga
    Posts
    692
    Oh ok..I'm in Henderson. North Vegas reminds me too much of los Angeles LOL...I o.ly go there to get a hair cut or pic a part..
    Reply With Quote Reply With Quote
  7. 03-05-2012 01:24 AM #7
    Handi770
    Handi770 is offline Junior Member
    Join Date
    Mar 2012
    Posts
    1

    replyz

    wait... op can you pm me.
    Reply With Quote Reply With Quote
+ Reply to Thread
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Forum Rules