Here's my run puttin the hurt on a Stang GT!!
Video of Mustang Run - Photobucket - Video and Image Hosting
Sorry for the bad quality....cell phone camera.
Here's my run puttin the hurt on a Stang GT!!
Video of Mustang Run - Photobucket - Video and Image Hosting
Sorry for the bad quality....cell phone camera.
2004 Silverado Crew Cab, forged iron 5.7, STS w/MP turbo, 10+ psi, FMIC, Tial 50mm BOV, Vic Jr, Snow performance meth, MTI Stealth cam .220/.220 .581/.581 115lsa, Comp chromoly pushrods, Yank TT3000 stall, LS1 Efans, 160 tstat, Trucool 40k trans cooler, 60# injectors, Walbro fuel pump, Patriot springs, Built 4l65E w/billet input & output shafts, Eaton posi, SD tuned...all installed by Klein North Automotive
nice run.
was there a lot of people out that night?
-leo-
2009 Silverado CC - 6.0L L76|6l80e|3.42s|4/7 drop w/ helper bags
01 silverado ecsb - (RIP 04/2009)
A win is a win.How much T/M are you still running,sounds like its pulling power down low.
Vortec Performance Tuned
LQ9 built 4L60 LTs and a billion miles on the speedo!
how in the heck do you hear that?Originally Posted by COWL327
i've read people's replies about them hearing stuff like that and i wonder that all the time.
is it because you know what to listen for? or what?
-leo-
2009 Silverado CC - 6.0L L76|6l80e|3.42s|4/7 drop w/ helper bags
01 silverado ecsb - (RIP 04/2009)
what was your time, like a 9.7-10.2?
There were quite a few people out there. It took about 35 minutes to get through the line to run.
As far as T/M, I'm not sure. Allen did my tune and I didn't specify anything to do with T/M. I'll have to ask him what he has it set at and if it would help to change it up a bit.
2004 Silverado Crew Cab, forged iron 5.7, STS w/MP turbo, 10+ psi, FMIC, Tial 50mm BOV, Vic Jr, Snow performance meth, MTI Stealth cam .220/.220 .581/.581 115lsa, Comp chromoly pushrods, Yank TT3000 stall, LS1 Efans, 160 tstat, Trucool 40k trans cooler, 60# injectors, Walbro fuel pump, Patriot springs, Built 4l65E w/billet input & output shafts, Eaton posi, SD tuned...all installed by Klein North Automotive
My time was a 9.0219 with a 2.1 60 ft and .4096 reaction time. I can just feel the 8's!!
2004 Silverado Crew Cab, forged iron 5.7, STS w/MP turbo, 10+ psi, FMIC, Tial 50mm BOV, Vic Jr, Snow performance meth, MTI Stealth cam .220/.220 .581/.581 115lsa, Comp chromoly pushrods, Yank TT3000 stall, LS1 Efans, 160 tstat, Trucool 40k trans cooler, 60# injectors, Walbro fuel pump, Patriot springs, Built 4l65E w/billet input & output shafts, Eaton posi, SD tuned...all installed by Klein North Automotive
Oh geeze..you can def. get down to the 8's easily! Get some 28.5" ET streets slapped on the back and you'll be there! Honestly, that 60' time is bad--but only due to traction reasons. Those ET's will help you cut some 1.8's!
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
Unfortunately I was running with the ET Streets on this pass!! I think I've narrowed down some of the issues though. Gearing is a big one (3.42's) but I'm not going to change it due to my lengthy commute. The other is that I only launched at ~2000 rpms when I should have been around 2800-3000. This would have cut my 60 ft to at least a 2.0 and time in the 8's!! There's always next time!!
2004 Silverado Crew Cab, forged iron 5.7, STS w/MP turbo, 10+ psi, FMIC, Tial 50mm BOV, Vic Jr, Snow performance meth, MTI Stealth cam .220/.220 .581/.581 115lsa, Comp chromoly pushrods, Yank TT3000 stall, LS1 Efans, 160 tstat, Trucool 40k trans cooler, 60# injectors, Walbro fuel pump, Patriot springs, Built 4l65E w/billet input & output shafts, Eaton posi, SD tuned...all installed by Klein North Automotive
Yeah, getting your launch nailed down will require a good amount of track time. Why did you only stall it to ~2000? Fear of the 60e tacking a crap on you?
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
Posting Permissions
Reply With Quote
