How would this work? what all is involved, is this the same basically as the ls6 intake swap. would it hurt me or be beneficial to my performance. i like the look and a few are available cheap. thanks for any help!
Dustin
How would this work? what all is involved, is this the same basically as the ls6 intake swap. would it hurt me or be beneficial to my performance. i like the look and a few are available cheap. thanks for any help!
Dustin
No don't do it. Will not flow as good. LS6 is better flowing.
12 Sec. Club! SOLD
La Viuda negra/ a.k.a. Black Betty
LQ4 6.0L, WCCH HEADS, LEVEL 5 FLT 4L80E TRANS. WITH TRANS BREAK, YANK 3200 STALL, TRICK TURBO, TURBONETICS T-76 TURBO, CUSTOM INTERCOOLED, 68lb INJECTORS, CUSTOM S/D TUNE FROM NELSON PERFORMANCE, COMP CAM 212/214 .557/.559 116+2, SNOW METH. KIT, . ALL INSTALLED AND DYNOED AT NELSON PERFORMANCE: 5**?HP @ 5073rpms and 5**TQ @ 4389rpms AT THE WHEELS WITH 10 PSI OF BOOST. ALL 3/4 TON TRUCK 5435LBS, NOTHING TAKEN OFF, STREET TIRES, AND USUALLY 2 BABY SEATS. WANNA RIDE?
SOLD***
What he said^^^^^
Also it depends o what you are using the truck for. The truck intake will have more TQ down low and the LS6 will have more power on the top end and let you rev higher also (I think)
1990 K2500 with Hummer Kit Body, LQ4, 4l80e 4x4
You will also have to relocate your accessories. Too much work for worse performance. I would suggest a FAST 90/90 intake over an LS6...
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
if i did a fast 90/90 id need new CAI, manifold, TB, MAF?, ACC bracket? what all would have to change?
The FAST 90/90 can be purchased with a 90mm TB--or without one. The FAST intake bolts right up and uses all the factory stuff. You would just need a CAI...
2000 ECSB 6.0L
TORQUER V2 CAM ● COMP 918's ● 7.4 HARDENED PUSHRODS ● K&N SERIES 77 CAI ● 80mm BBK ●PACESETTER LT HEADERS AND 3'' ORY ● SUPER 40 FLOW ● 3000 STALL ● 4.10s ● BUILT 80e ● VORTEC PERFORMANCE TUNE ● MSD 8.5mm PLUG WIRES● ELEC. CUTOUT ● UD & ALT PULLEYS ● FLEX-A-LITE E-FANS ● 22" CENTERLINE STINGRAY III's ● LUND FIBERGLASS TONNEAU ● 2" LEVELING SHACKLES ● 12K HID LOWS & FOGS ● LEDs ● DEBADGED ● WHITE-FACED ESCALADE GAUGES ● KICKER 450.1 ● 2-CVR 10's ● DS60's ● K693's
Posting Permissions
Reply With Quote
