In the market for another cam.
Some were in the mid 230 to low 240 with a 112 ish lsa.
Lmk what you have thanks
As always, the cheaper the better
Type: Posts; User: LOWnEASY
In the market for another cam.
Some were in the mid 230 to low 240 with a 112 ish lsa.
Lmk what you have thanks
As always, the cheaper the better
Looking for a cam for a 5.3. Something in the 22x/22x rang with 108-112 lsa. 200-$250 shipped would be nice as well. Lmk what u got.
Have an gmpp asa cam for sale or trade. 226/236 110 lsa 525/525. 100-150 miles on it.
Easy on the valve springs (can run ls6 springs and not worry about them for thousands of miles), sounds wicked,...
Ahh, didn't know that. Sorry
So the bolts are bottoming out?
If it's the factory 6.0 bolts, and was in front of an auto, it most likely had a flex plate spacer that's .4 thick
I had a nv3500 5 speed behind a 4.8 and used...
How does that thing shift 5500+? Mine didn't even like 3500+ rpm.
I second the 87+ tanks, my 95 4.8/4l80 gets starved of gas under hard launches will 1/2 or less tank due to the gas all going to the back. Full down to 1/2 is fine.
Those tanks are setup to run a...
My 4.8 keeps cranking with the key off but I can disconnect the battery then connect it back and it doesn't do it again until I hit the key. Wtf is up with it? Solenoid? Relay?
I'll take the wideband Friday if you still have it.
Can't believe no one has got this.
This guy is a good seller too!
I'm hoping it works good with BOOST! Haha. Not going for max effort, but some say what adds power N/A will add power F/I,
Told the wife I "had" to have HP tuners to tune for the cam(little does she...
Bought the one from kerrige! Thanks
Pm'd kerrige
Looking for a good deal on a cam for around ~250-275. Needs something that will work good in a 4.8 so nothing over a 228 @ 50(and thats already pushing it) Prefer something with a 110-112 LSA. Don't...
95 rcsb 4.8 4l80e
Wot with half or less tank of gas, it cuts out. Full tank down to half does fine. My gas gauge bounces bad, so I can watch it hit E when I have a 1/2 tank. Any one know what I...
If its the one inch set back mounts, then the transmission will remain in the stick location. If it isn't the 1" set back mounts then the trans cross member will have to be moved, front shaft...
Now it doesn't want to find any gear. I have to put it in park then slam it down to first (on gear shifter b&m floor shift) then back up to drive to go.
I just got done swapping a 4l80e in my 95rcsb and all is well except I'm only counting 2 shifts and converter lock up. It has 3.42 gears and turns ~2000 rpm a 55.
Does the converter only lock in...
What happens to the login I'd of the site that had all the diagrams that's in some peoples signature? Starts with am e, cant think of the name.
It was
User name: student
Password: Watc
That would throw a code wouldn't it?
What about a vacuum leak? I did have my intake off during the swap and put it back on with the original gaskets It idles around 550-600 rpm in park and its a...
Just got done with my 4l80e swap and got it buttoned up today. Took it on a test drive and it spits and spiders under 4k rpm and no power. After 4k it picks up and goes. Also_), there is no check...
Pair of 862 heads, two inake valves need replaced (water sat on them and rusted up) other than that there in good shape. $100 shipped obo. Dont know what there worth so make an offer
Truck fuel...
Wth happened? Looks like it was drilled or something...
Nelson will do it.
Actually, this is a 2wd unit. I figured out that it had a parking brake attached for a heavy duty box truck or van.
I'm hopeing I can find a seal to fit, and remove the bearing.