Does anyone know what the torque pattern is for the 4L80 pan bolts? Also, do I need to lubricate the gasket with trans fluid prior to installation?
Type: Posts; User: jetmech
Does anyone know what the torque pattern is for the 4L80 pan bolts? Also, do I need to lubricate the gasket with trans fluid prior to installation?
Bump for a good seller. I bought one of these for my 4L80 swap, works great :burnrub:
I think I'm in love!
The truck in my garage, with the following upgrades:
~ 427 LSX
~ Twin turbos
~ 4 Link
~ and a few other things I'm probably forgetting
The engine compartment is a real mess, I know, but I'm in the process of tuning (having Allen tune it, actually) and cleaning everything up. it's still a work in progress, but running strong none the...
I've been working through some issues, but solving them none the less. I should be able to get some pics uploaded later today.
It turns out the tune I had was causing all the issues - the clowns here in south Florida don't know what they're doing. Allen, thanks for rescuing me. The truck is running really well now - one data...
Would you be able to tell by looking at the tune? At this point I'm willing to send you the PCM and get a second opinion. The truck takes throttle just fine when sitting in the driveway revving the...
It stumbles like crazy, I hit the throttle and hold my foot steady, yet the truck behaves as though I am tapping the throttle. I can make it into second gear, beyond that I lose all faith in the...
Got it. Next question:
If the truck is in "limp mode", would it behave as I have described in my original post? I've heard of a bad knock sensor throwing the PCM into limp mode and causing a great...
I've run SD tunes in the past and never seen a MAF code. That is what has me concerned.
P0054 - H02S Heater resistance (bank 1 sensor 2)
P0060 - H02S Heater resistance (bank 2 sensor 2)
P0102 - Mass or volume air flow circuit low input
P0103 - Mass or volume air flow circuit high...
I've been having electrical issues so I've been looking at wiring diagrams a lot lately. During my studies of these diagrams, I noticed that some describe a RED retainer on the PCM connector where my...
I'm having an electrical problem which I am almost positive is a ground issue. If I am not mistaken, 4 grounds attach to the block - (1) large gauge wire (looks like 4 or 2 AWG) which attaches to the...
My truck is an '06 and came with a 4L60. I hear some trucks came with a separate trans controller if a 4L80 is factory equipped. So what do you do if you swap from a 4L60 to a 4L80 and your truck...
I may be moving to Arizona and I'm trying to figure out what kind of emissions laws, if any, the state of Arizona has. Any Arizona residents on this site?
Update coming soon...
Any recommendations for a good serpentine belt that will handle a lot of power?
sold
I picked up a Duramax MAP sensor, part # 12623671 (3 bar I think). I plan to run up to about 18 psi on this build. Will this MAP sensor work well for what I'm trying to do?
Price drop, $800 plus shipping
I'm swapping to a 4L80E, so this transmission needs a home. This 4L60E was built less than 3 years ago and has only seen about 10,000 miles of use. It's a stock transmission with a shift kit. Asking...
What is a good set of 95 lbs/hr injectors (@ 4 bar) or something close to that? Preferably a set with an impedance that will work well with the factory VCM. Also, what are a good set of aftermarket...
Let's face it, stereotypically a person who drives a Chevy truck will at least have some interest in country music. Country may not always be my first choice, but I do enjoy it. So as the title says,...
This is my first rodeo with the mighty 4L80, so I am in uncharted territory of sorts. Still, part of the fun is figuring out how something else works!