Search:

Type: Posts; User: DBRODS

Page 1 of 5 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    7
    Views
    2,291

    You can go up to 0.035 off the heads without...

    You can go up to 0.035 off the heads without alignment issues and as always you should check PTV. But that cam wont have any issues with clearance!
  2. Replies
    67
    Views
    9,859

    317s or 243/799 would work. I would prefer to...

    317s or 243/799 would work. I would prefer to see the 243/799 heads due to the increase in compression and added NA power as George stated. The chambers on my heads on my L33 5.3 are 64cc. That...
  3. Replies
    67
    Views
    9,859

    Yeah replacing rod bolts is a gimmick also. If I...

    Yeah replacing rod bolts is a gimmick also. If I turn the boost up over a certain level I can guarantee it will bend the rods up as I've done it a few times. Usually everyone blames the rod bolts...
  4. Replies
    7
    Views
    2,291

    I would deck the heads before touching the block....

    I would deck the heads before touching the block. A stock l33 piston is gunna stick out of the hole around 0.006. If you knock off 0.020 that only leaves you with .0.025 between the piston and head...
  5. Replies
    67
    Views
    9,859

    You are completely wrong. A bad tuneup kills...

    You are completely wrong. A bad tuneup kills ring lands and bearings. The stock rods will bend up before a piston has a failure or a rod bolt lets go.
  6. Replies
    1
    Views
    1,260

    Sold!!!

    Sold!!!
  7. Replies
    1
    Views
    1,260

    Jakes D3 transbrake 4l80e

    Jakes D3 transbrake for a 4l80E 97 and newer. I swapped to a D1 brake and no longer need it. It was only used for a few months. Ill take 450.00 shipped. I payed 650.00 new. Also comes with a...
  8. Replies
    43
    Views
    7,165

    I broke a input shaft a few weeks ago and it...

    I broke a input shaft a few weeks ago and it still had Park. No forward gears or reverse. Just a FYI
  9. Replies
    30
    Views
    3,021

    The pumps start at 550.00, then a high flow...

    The pumps start at 550.00, then a high flow regulator to mach it probably 200.00 and a crank mandrel is 200.00 with belts and pulleys. Then it needs huge fuel line for feed -12 or bigger. It adds...
  10. Replies
    67
    Views
    45,083

    They don't make anything above a 800lb spring in...

    They don't make anything above a 800lb spring in a 10". The 8" spring has more options all the way up to 1200lb. There is no ride quality difference between a 8" or a 10". I've tested many combos.
  11. Replies
    30
    Views
    3,021

    Good to see that took care of the issue. The...

    Good to see that took care of the issue. The belt drive gets a little pricey. It wont work with a stock crank pulley. You have to be able to mount a mandrel.
  12. Replies
    30
    Views
    3,021

    The notch is probably the issue with the line up...

    The notch is probably the issue with the line up high. I personally like to have electric pumps as close to the tank as possible. If you can get the high spots out pre pump with a lowered pump you...
  13. Replies
    30
    Views
    3,021

    Heres what my fuel system consist of and...

    Heres what my fuel system consist of and locations. Sorry if its a little dirty, street truck. I ended up adding a inline small pump that is wired to the starter solenoid. The Belt driven pump...
  14. Replies
    30
    Views
    3,021

    With my setup I had issues keeping the pump...

    With my setup I had issues keeping the pump primed with the fuel line running along the frame next to the cnotch. The line is so high right there that it would create a air pocket and then the pump...
  15. Replies
    30
    Views
    3,021

    I'd like to see the pump a little lower than...

    I'd like to see the pump a little lower than that. Maybe 3-4" lower.
  16. Replies
    30
    Views
    3,021

    Yup, I love my belt driven pump.

    Yup, I love my belt driven pump.
  17. Replies
    30
    Views
    3,021

    I thought those were yours but couldn't remember....

    I thought those were yours but couldn't remember. Yeah that pump placement is fine. Even a inch or two higher would still be ok. Just be sure to keep at least a 1/4 tank when doing wot pulls to be...
  18. Replies
    30
    Views
    3,021

    Pretty much in this position. ...

    Pretty much in this position.

    http://i282.photobucket.com/albums/kk272/dbrods/408B6A2C-EB94-4CE9-8154-AB0006DE8A3E-4770-000001A816919283.jpg
    ...
  19. Replies
    30
    Views
    3,021

    Can you mount the pump off one of the fuel cell...

    Can you mount the pump off one of the fuel cell mounts. Maybe make a plate that can bolt to one of the mounting tabs on the cell. Almost right where the hose clamp is at in your pic? I thought you...
  20. Replies
    30
    Views
    3,021

    If you could mount it behind the tank hanging...

    If you could mount it behind the tank hanging down it would be ideal. Get it as close to the bottom of the tank as possible. Definitely sounds like its a little high.
  21. Replies
    16
    Views
    1,743

    Those are awesome. Too bad I'm not into emblems...

    Those are awesome. Too bad I'm not into emblems or stickers!!!
  22. Replies
    228
    Views
    20,483

    Awesome!!!

    Awesome!!!
  23. Replies
    67
    Views
    45,083

    Sorry I was out on vacation last week. Sent ya a...

    Sorry I was out on vacation last week. Sent ya a email Jared!!
  24. Replies
    74
    Views
    11,991

    Thats Badass!!!! Congrats again. We tried...

    Thats Badass!!!! Congrats again. We tried everything to get that thing to hook on radials but the split is too much!! The Poly bushings have held mid 1.30s consistently on our street/strip stuff...
  25. Replies
    74
    Views
    11,991

    That s10 has been high 8s. Thank you sir, but...

    That s10 has been high 8s.

    Thank you sir, but I cant take all the credit. SC the original owner did a lot of the work himself.

    Thanks its never too far for something that works!!!! Plus...
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4