Search:

Type: Posts; User: brianmcb

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    479

    Oh and bring a hack saw incase you can't get the...

    Oh and bring a hack saw incase you can't get the 15mm exhaust manifold bolts off. They are a sombitch
  2. Replies
    3
    Views
    479

    Fuel line disconnect tools unless you just cut...

    Fuel line disconnect tools unless you just cut the hose. Bring lots of extensions to get the belhousing bolts
  3. That's the code for the trans range sensor...

    That's the code for the trans range sensor (prndl)
    Just turn that code off if you have hp tuners
  4. Thread: 5.3 swap

    by brianmcb
    Replies
    2
    Views
    808

    Sachs nfw1050 is the flywheel you need. Your...

    Sachs nfw1050 is the flywheel you need. Your current clutch will work fine.
  5. Replies
    2
    Views
    1,260

    I am running a 219/228 112LSA hot cam with ls6...

    I am running a 219/228 112LSA hot cam with ls6 springs...according to all the keyboard master mechanics, its an old school cam, but it sure pulls hard (sounds sweet to)

    IIRC the ls6 springs are...
  6. Replies
    3
    Views
    975

    This forum has as much life as a cemetery, you'd...

    This forum has as much life as a cemetery, you'd be better off searching on ls1tech
  7. And of course you neee the two harnesses that...

    And of course you neee the two harnesses that plug into the tac module
  8. Did it in my 95. Not hard at all. Need the...

    Did it in my 95. Not hard at all. Need the pedal, and tac module. Had to modify the metal pedal bracket to fit the truck properly, so i wouldn't recommend the all plastic version of the pedal.
  9. Replies
    6
    Views
    1,949

    I used the original fuse box. Wired into the...

    I used the original fuse box. Wired into the stock fuel pump relay and everything. Looks "factory" and clean
  10. Replies
    6
    Views
    1,949

    Lt1swap.com does. Thats what i used as a...

    Lt1swap.com does. Thats what i used as a reference
  11. Replies
    2
    Views
    1,155

    Yes you can use stock rad. Your stock lower rad...

    Yes you can use stock rad. Your stock lower rad hose will work, but use the donor truck top hose.

    You cant use the donor ac unit in its stock location, you'll have to usr your stock one and run...
  12. Replies
    4
    Views
    1,094

    Sent you a pm few days ago about my swap

    Sent you a pm few days ago about my swap
  13. Replies
    4
    Views
    1,621

    Www.lt1swap.com

    Www.lt1swap.com
  14. Replies
    2
    Views
    941

    They fit. Had them on my truck when I set the...

    They fit. Had them on my truck when I set the engine in place. Then my long tubes showed up the next day
  15. Replies
    2
    Views
    577

    Stock one from my 4.3 v6 works just fine. Stock...

    Stock one from my 4.3 v6 works just fine. Stock throw out bearing works fine to
  16. Replies
    3
    Views
    805

    Works fine either way. No noticeable difference

    Works fine either way. No noticeable difference
  17. Replies
    3
    Views
    805

    I used a cheap eBay kit for a hummer h2 for a...

    I used a cheap eBay kit for a hummer h2 for a while. Worked good just ugly IMO. Now I'm just running a cone filter right off the throttle body with a 4" flex coupler
  18. Replies
    3
    Views
    821

    Little quick math with gear ratio and tire...

    Little quick math with gear ratio and tire diameter and speed will tell you exactly cruising rpm. Probably even a calculator online that you can punch the numbers into
  19. Replies
    3
    Views
    821

    Put taller gears in it. 342's should not be on a...

    Put taller gears in it. 342's should not be on a "tow package" vehicle. 3:73 or 4:10 would make it tow good
  20. Replies
    3
    Views
    1,362

    They are different springs if they are truck 799...

    They are different springs if they are truck 799 heads. I put the blue ls6 springs in my 799s for my hotcam.
  21. Replies
    6
    Views
    1,478

    Just build your own, it's super easy. Lots of...

    Just build your own, it's super easy. Lots of videos on YouTube about it also. You can also extend your wires and hide your pcm wherever you want
  22. Replies
    1
    Views
    3,780

    Post pics when you get to it. Been curious about...

    Post pics when you get to it. Been curious about it myself
  23. Thread: Wiring issues

    by brianmcb
    Replies
    2
    Views
    1,108

    Go to lt1swap.com All the info you could ever...

    Go to lt1swap.com
    All the info you could ever need. I threw the 5.3 fuse block in the garbage and just ran everything into my factory block. A multimeter and a test light are your best friend
  24. Replies
    121
    Views
    52,062

    That truck is the same color that mine started...

    That truck is the same color that mine started life as. Mines currently stripped to bare metal and doing body work and prep for paint. Tough to decide on a new color!
  25. Replies
    121
    Views
    52,062

    Love it.

    Love it.
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4