I'm going to be using colorbond on my dash and interior. Not planning on removing the dash.
Type: Posts; User: HRV-LS1
I'm going to be using colorbond on my dash and interior. Not planning on removing the dash.
Took it dealer. Waiting for them to let me know what they find. Its going to take them a few days. Have a feeling that the 1 condition for a dtc " odometer more than 10 miles " is whats preventing it...
If I go the dealer with this problem, will it be pricey to take care of? I think its a $95 just for a diagnostic.
Got a question. When I'm driving the truck at 65mph., the rpm is 2300. The rear axle ratio is a stock 3.42. The tires are 255/55R17. Does the rpm sound right on for this or is it too
high?
You can't use your 94 4l60e trans. It needs to be 95 and newer, because the 94 doesn't have enough pins in the trans. socket connector. Got to be 95 and newer.
I'm still driving the truck with the 2 monitoring systems " not ready or yes". I'll keep going, and going,......
Are there any other good scan tools to purchase other than hp tuners or efi? I'm looking for something that will be able to command tests ( EVAP, O2 SENSOR, MONITORING SYSTEMS), as well as show...
Today took it for a drive on the freeway. Went a total of 65 miles. Stopped for an hour. Drove back, let it sit for a few hours, same problem. The evap & o2 monitoring systems still have not...
It is a pain in the a***. When you mean don't lose power to the pcm, do you mean don't shut the motor off or don't disconnect the battery? In the manual instructions, they mention don't turn off the...
Did a 5.3 swap in my 95 GMC. The trucks a Calif. emissions truck. All components there for emisssions. The scanner blinks o2 & evap. monitoring not complete. How many times do I need to drive it...
Got the label I needed. There was confusion on my part at the dealer. Anyway, hooked a scan tool to the ecu port, and I don't have any alarm codes. The only problem is now that 2 monitoring systems...
Got one problem. On my airfilter housing box, theres a vehicle emissions info label there. The problem is that it shows its for an 2004, my engine and ecu are 2003. That may cause a problem with the...
Yes, no, anybody??
Is there a kit for our OBS fuel tanks, where you install internal baffles to keep the fuel gauge from doing the wave?
Does anybody know the part number for the anti-wave action plate that goes in the obs fuel tanks? Got wave action on the needle. I'm sure its not exactly called like that, but I hope you understand.
Its ok. The top one is hot, and the bottom is cooler. should be fine.
Should both of my radiator hoses be extremely hot, upper and lower? I believe there is plenty of coolant in the engine and radiator. Took it for a ride, engine temp gauge reads normal.
Do you have a particular scanner in mind?
Currently installing new brakes. Going to get new wheels/ tires. Also, need to send out my airbag module. It has a light on all the time. I'll try looking for a place to send it that can tell me why...
Got it idling at 650. Idles smooth. Tons of power. Took it for a drive, and it's fantastic. The dbw is awesome. Never owned a V8 in my life, this 5.3 is terrific. Its exactly what I wanted.
Update. Got the truck running and shifting correctly. Speedometer works also. Just reversed the old vss wires at the new vss connector and, viola it works! Also hooked up the new fuel pump relay,...
They made a brand new wiring harness for me. The engine came with a harness, pcm, etc. The new connector that goes to the trans selector, has 1 wire in the connector. The old one
has 6 wires. I...
The new pcm is suppose control the engine and trans. When I plugged everything in, it couldn't start and there was no indicator light at the selector switch. I thought I was suppse to plug in all of...
Who did your harness? S & P did mine. At the start all the new plugs were plugged in. But the truck wouldn't start, no power to selector switch. Plugged back 2 old plugs at selector switch, and truck...
The pcm was handled by S & P. They removed the vats, put in tire size and rear gear ratio. The pcm is suppose to run the engine and trans, for all I know. I believe the suburban had a 4l60e behind...