Search:

Type: Posts; User: lost06

Page 1 of 3 1 2 3

Search: Search took 0.05 seconds.

  1. Thread: Wire

    by lost06
    Replies
    3
    Views
    851

    Wire

    What kind of wire would I need to buy to build my own harness, and where would I find it? The one I have is a mess and want to clean up the engine by re-routing wires and relocating the PCM.
  2. Thread: Starting issues

    by lost06
    Replies
    11
    Views
    4,130

    I had a similar problem. I had a bad ground and...

    I had a similar problem. I had a bad ground and the O2's were bad.
  3. Thread: Spark plugs

    by lost06
    Replies
    6
    Views
    2,106

    X2 on not adjusting the gap.

    X2 on not adjusting the gap.
  4. Replies
    7
    Views
    906

    When I got my harness back, it was wrapped with...

    When I got my harness back, it was wrapped with electrical tape. And I'm noticing that it doesnt like heat at all.
  5. Replies
    7
    Views
    906

    The guy who did my stuff is out of Arkansas. I...

    The guy who did my stuff is out of Arkansas. I think his business is called LSX harnesses. Ill see about the evap stuff. And I did find a couple places where wires were resting on the engine.

    Has...
  6. Replies
    7
    Views
    906

    After the swap...

    I just finished a 5.3 - 4L60E conversion into a 1996 Sierra. I need a little info on a couple of things. These are mostly "is this normal" questions...

    1. The damn thing idles like crap. It shakes...
  7. Replies
    16
    Views
    1,663

    I took a small hammer and tapped on the rails....

    I took a small hammer and tapped on the rails. Bam!!!! It fired up. Thanks for the help!
  8. Replies
    15
    Views
    2,762

    out of all the things involved I tried to save...

    out of all the things involved I tried to save money on my harness. BIG mistake. I paid $450 for a POS. Now I am going to cough up another $650 for a good one. Most people use Nelson performance....
  9. Thread: Trans lines

    by lost06
    Replies
    9
    Views
    1,161

    well, I went to the parts house with my radiator...

    well, I went to the parts house with my radiator under arm. They had the fittings I needed for the radiator. I cut the hard lines and put compression / barbed fittings and it worked like a charm......
  10. also, there are a hundred other little things...

    also, there are a hundred other little things that will add up to make the swap happen. all of the wiring issues, fuel pump / lines, computers, motor mounts....
  11. Thread: Trans lines

    by lost06
    Replies
    9
    Views
    1,161

    I wasn't sure if it would fit.

    I wasn't sure if it would fit.
  12. Thread: Trans lines

    by lost06
    Replies
    9
    Views
    1,161

    I was trying to not spend the money. But I think...

    I was trying to not spend the money. But I think an aftermarket cooler is the way to solve it.

    Can I just leave the radiator holes open?
  13. Thread: Trans lines

    by lost06
    Replies
    9
    Views
    1,161

    Trans lines

    I have a question on how to tie in my trans lines to my radiator. I put an 05 5.3 and 4l60e in my 96 sierra. I am using my 96's radiator and the trans lines from the 05. The 05 uses different...
  14. if it isn't broken.... unless the 406 is on its...

    if it isn't broken.... unless the 406 is on its way out, I would keep it until it keels over.
  15. Replies
    16
    Views
    1,663

    thanks guys. after i get home from my boys...

    thanks guys. after i get home from my boys wrestling tournament, i'll start tearing it down.
  16. Replies
    16
    Views
    1,663

    stock pump from the 96 thru a vette filter to the...

    stock pump from the 96 thru a vette filter to the stock 5.3 fuel rail and injectors.
  17. Replies
    16
    Views
    1,663

    ok. i didn't pull any plugs but i did go out and...

    ok. i didn't pull any plugs but i did go out and spray some starter fluid in the t.b. and it fired up and ran for about 5 seconds.
  18. Ahhh, I see. My motor has been sitting for a year...

    Ahhh, I see. My motor has been sitting for a year that I know of so that's where I'll start. Thanks.
  19. Replies
    16
    Views
    1,663

    This guys out of Arkansas.

    This guys out of Arkansas.
  20. Replies
    16
    Views
    1,663

    I'm not much of an electrical whiz. What's the...

    I'm not much of an electrical whiz. What's the easiest way to check for spark?

    The guy who did my computer just removed the rear O2's, vats, etc; but nothing performance wise.
  21. Replies
    16
    Views
    1,663

    dumb ? , but i have to ask...

    i am having a problem. I cant get my truck to start after swapping an L33 into a 96 Sierra.

    I am wondering if not having my O2 sensors installed will prevent it from starting?

    It cranks, and I...
  22. i am having a similar problem. did you ever find...

    i am having a similar problem. did you ever find a solution?
  23. Replies
    6
    Views
    2,042

    So I solved the problem, it was really simple. I...

    So I solved the problem, it was really simple. I grounded that set of grounds to the coil bracket on the valve cover. Apparently, this is a bad idea. I moved the ground to the alternator bracket and...
  24. Replies
    19
    Views
    2,931

    yeah, it was really simple. I grounded that set...

    yeah, it was really simple. I grounded that set of grounds to the coil bracket on the valve cover. Apparently, this is a bad idea. I moved the ground to the alternator bracket and my gauge started...
  25. Replies
    19
    Views
    2,931

    Please see my post here....

    Please see my post here. http://www.ls1truck.com/forums/lsx-truck-conversions/44931-no-fuel-please-help.html

    it might be a little more descriptive.

    Thanks for the help and advice
Results 1 to 25 of 57
Page 1 of 3 1 2 3