Search:

Type: Posts; User: ImportThis

Page 1 of 5 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    4,123

    I saw these a while back and have really been...

    I saw these a while back and have really been thinking about coil over conversion to drop my Z71. But it requires $$$ which I don't have much of lol
  2. Replies
    6
    Views
    1,423

    No cats here. Not until they start using a...

    No cats here. Not until they start using a sniffer
  3. Replies
    19
    Views
    4,633

    Awesome looking truck

    Awesome looking truck
  4. Replies
    2
    Views
    1,862

    Pull it out and build it. And time for a stall...

    Pull it out and build it. And time for a stall while you're in there
  5. Replies
    20
    Views
    4,950

    You probably could of built a 370 or 408 for what...

    You probably could of built a 370 or 408 for what the iron 5.7 cost.
  6. Go 6.0!! Honestly if there's nothing wrong with...

    Go 6.0!! Honestly if there's nothing wrong with the 6.0 short block I wouldn't tear it apart. I have a ccsb z71 with a cammed/milled heads/stalled 5.3/4L60 and 3.42s, I avg 10 in town (because...
  7. Replies
    13
    Views
    5,496

    They are wearing very little, and very smooth. ...

    They are wearing very little, and very smooth. They have almost 10k miles. Been rotated once. I figure I will get 40k+ out of them. My last set was buckshots and I got 33k out of those
  8. Replies
    13
    Views
    5,496

    TOYO Open Country A/T 2 is what I run. Nitto's...

    TOYO Open Country A/T 2 is what I run. Nitto's will wear too fast. I've never heard anything good about the Grabbers. I've seen quite a few sets of Grabber MT's come apart, don't know if the AT's...
  9. Thread: Oil change

    by ImportThis
    Replies
    9
    Views
    4,746

    I thought the oil life monitor was based on...

    I thought the oil life monitor was based on engine rpm, not actual mileage. My 05 May vary 6-800 miles from 100-0%.
  10. Thread: Oil change

    by ImportThis
    Replies
    9
    Views
    4,746

    Go ahead and swap to a good oil now and change it...

    Go ahead and swap to a good oil now and change it yourself. I'm running amsoil 5w20 in mine. But it has 190k on it. But I have to pay a place 12 bucks to change it for me cuz all my tools are at...
  11. Thread: Oil change

    by ImportThis
    Replies
    9
    Views
    4,746

    I just spent 60 bucks today getting the oil...

    I just spent 60 bucks today getting the oil changed on my truck.
  12. Replies
    3
    Views
    1,540

    I just thought my computer didn't like y'all...

    I just thought my computer didn't like y'all anymore
  13. Replies
    18
    Views
    2,648

    Any Spintech is loud af.

    Any Spintech is loud af.
  14. Replies
    18
    Views
    2,648

    To decipher for the guy that confuses the hell...

    To decipher for the guy that confuses the hell out of autocorrect, if you want performance and quality, use magnaflow, borla or Spintech. Flow masters don't really flow that we'll, known to rust...
  15. Replies
    18
    Views
    2,648

    What kinda idiot runs flowbastards anymore. If...

    What kinda idiot runs flowbastards anymore. If you want loud, go Spintech
  16. Thread: CCSB drop

    by ImportThis
    Replies
    5
    Views
    736

    I've been contemplating a 2/4 drop on my cc z...

    I've been contemplating a 2/4 drop on my cc z also. But haven't had much time to research it very much
  17. Thread: Driveshaft

    by ImportThis
    Replies
    7
    Views
    1,434

    You probably won't find a factory one that is a...

    You probably won't find a factory one that is a direct fit 1 piece. If the length isn't too long you could have a custom shaft built. Just remember, the longer the tubing of your shaft, the weaker...
  18. Thread: Driveshaft

    by ImportThis
    Replies
    7
    Views
    1,434

    If you're buying joints from a parts store,...

    If you're buying joints from a parts store, that's why you keep replacing them. The tolerances on parts store joints are not very close and cause lots of failure issues. I worked at a driveline...
  19. Replies
    15
    Views
    1,900

    Don't put a flowbastard on anything. Waste of...

    Don't put a flowbastard on anything. Waste of money. Go Magnaflow for quiet or Spintech for badass.
  20. Replies
    35
    Views
    7,740

    If you want loud, go Spintech. Quiet idle and...

    If you want loud, go Spintech. Quiet idle and throaty at WFO, big body Magnaflow
  21. Replies
    2
    Views
    681

    That's not bad deal at all. I just paid 750 for a...

    That's not bad deal at all. I just paid 750 for a set of those tires 6 months ago.
  22. If you ever want to sell your headlights I WANT...

    If you ever want to sell your headlights I WANT THEM. Damn things are impossible to find
  23. When you gonna stab the motor? I'll come help if...

    When you gonna stab the motor? I'll come help if it's on the weekend. We can send the women somewhere lol
  24. Replies
    6
    Views
    1,199

    Does your pos wire from the back of the alt run...

    Does your pos wire from the back of the alt run strait to the battery, or does it go elsewhere? It honestly sounds like you have a loose ground somewhere. Could be anywhere. Make sure you have a...
  25. Replies
    6
    Views
    1,199

    Haha autozone idiots are so funny. A starter has...

    Haha autozone idiots are so funny. A starter has 0 draw unless its turning. But, which alt are you running, 2 wire plug or 4 wire plug? If its the 4 wire plug, make sure the wire going into it is...
Results 1 to 25 of 118
Page 1 of 5 1 2 3 4