Search:

Type: Posts; User: Ray@NP

Page 1 of 5 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1
    Views
    350

    pin 20,57 on connector one should have battery...

    pin 20,57 on connector one should have battery voltage
    pin 19,75 on connector one should have ignition
    pin 1,40 on connector one are both ground along with 1,40 on connector 2
  2. Replies
    1
    Views
    384

    if noid light is staying on while running that is...

    if noid light is staying on while running that is a issue with the ecm
  3. Replies
    3
    Views
    774

    you will need basic socket set, some pliers and...

    you will need basic socket set, some pliers and some wire cutters. I would also take a long prybar also.
  4. Replies
    4
    Views
    1,405

    we can build you a stand alone engine harness for...

    we can build you a stand alone engine harness for your swap and supply you with tuning.
    if you have any questions email info@nelsonperformance.com
  5. Replies
    2
    Views
    1,183

    use the factory style steel gaskets

    use the factory style steel gaskets
  6. Replies
    2
    Views
    1,182

    i usually leave the trans in the truck and...

    i usually leave the trans in the truck and install the engine that way you aint fighting to line both up just the sliders
  7. Replies
    4
    Views
    1,498

    do you have any pressure sensor hooked up going...

    do you have any pressure sensor hooked up going to he ecm
  8. we can build you a custom stand alone engine...

    we can build you a custom stand alone engine harness for this combo. email info@nelsonperformance.com for more details
  9. we can build you a stand alone harness for the...

    we can build you a stand alone harness for the conversion. you can use the 7oor4 but if you plan keeping the 03 drive by wire the only issue i see is hooking up the tv cable. for more info on the...
  10. Replies
    3
    Views
    1,108

    if you are going drive by cable the harness is...

    if you are going drive by cable the harness is $640 drive by cable is $850
  11. Replies
    2
    Views
    1,099

    were you able to scan the truck to see what the...

    were you able to scan the truck to see what the issues were?
  12. Replies
    1
    Views
    1,681

    yes you can use the original 60e or you can use...

    yes you can use the original 60e or you can use the 60e from the 6L. you can get dirty dingo ls swap mounts that way you dont have to change trans cross member location. We can build you a custom...
  13. Replies
    2
    Views
    764

    sound like a badass build cant wait to see some...

    sound like a badass build cant wait to see some progress pics
  14. Replies
    3
    Views
    1,108

    we can build you a stand alone harness for your...

    we can build you a stand alone harness for your truck that will look really nice. sounds like you have everything covered as far as mounts go, Is the 4l60 out if the 93 electronic? If you have the...
  15. Replies
    3
    Views
    1,238

    we use the LSsimple kit, looks and works great

    we use the LSsimple kit, looks and works great
  16. Replies
    3
    Views
    1,718

    You cant use the 2 wire knock sensors with your...

    You cant use the 2 wire knock sensors with your 01 pcm
  17. Replies
    3
    Views
    1,718

    you can drill and tap the side of the block where...

    you can drill and tap the side of the block where the 09 knock sensors bolt into and install your factory sensors since they are 1 wire, then just extend you wiring to the side of the block

    you...
  18. Replies
    1
    Views
    924

    that pcm will work for your swap. all your...

    that pcm will work for your swap. all your factory gauges can still function with a few wiring modifications, even the a/c controls. I see you have the original harness that came with the engine, but...
  19. Replies
    9
    Views
    5,951

    keep up the good work, im sure lots of guys are...

    keep up the good work, im sure lots of guys are following this build
  20. Thread: Hi y’all

    by Ray@NP
    Replies
    1
    Views
    475

    welcome to the site

    welcome to the site
  21. Thread: Obs lq9 swap

    by Ray@NP
    Replies
    1
    Views
    578

    what car intake are you using? you will need to...

    what car intake are you using? you will need to cut your alt bracket if you are running truck accessories and may need to use a ls1 water pump if you are running a aftermarket mechanical throttle body
  22. Replies
    14
    Views
    1,790

    you can get some dirty dingo conversion mounts,...

    you can get some dirty dingo conversion mounts, set the engine/trans into the truck and that will determine if you need to move your crossmember or if you can use it. As far as the column, there are...
  23. Replies
    5
    Views
    1,663

    i would go with a aeromotive 340 stealth, its...

    i would go with a aeromotive 340 stealth, its really not hard to install. just separate the pump basket and cut the old pump out, install the new pump and plug in the provided harness
  24. Replies
    6
    Views
    1,561

    we can build you a custom stand alone harness...

    we can build you a custom stand alone harness just give us a call 2106260278 or email info@nelsonperformance.com
  25. a new radiator will fix it but you can try some...

    a new radiator will fix it but you can try some CLR and water just run it through your system and flush it that way
Results 1 to 25 of 118
Page 1 of 5 1 2 3 4