well all good times come to a end guys, i have a baby on the way and to many toys so something has to go. unfortunately it has to be my silverado. i am the original owner of this truck and have kept...
Type: Posts; User: liftedboost
well all good times come to a end guys, i have a baby on the way and to many toys so something has to go. unfortunately it has to be my silverado. i am the original owner of this truck and have kept...
Well long story short , i snapped the output shaft in half, had the transmission rebuilt by a reputable shop (bench job) and i removed/installed myself. Installed a Hardened output shaft .
have...
That's what I was figuring, I think the heat wrap held water and moisture and rusted through. Waiting on new weld flanges to come in and weld up a new section and definitely leaving the heat wrap off...
8197
Well I was wondering why I lost boost lol, no buenos
I was wondering if this could be from heat wrapping causing it not to dissipate the heat?
Going to hook up pyrometer as well , I've...
Great info and thanks! Want to be sure on what I'm getting
Ok I found a rear axle off a 06 silverado ss 2wd with A locking 4.10s for a decent price and was wondering if it should be a bolt up and go?
Also I have rear drums on mine so I'm guessing it won't...
I have the 4l60e that took 4 rebuilds to get it where it's at now and surprisingly it's holding strong . But eventually doing a 80e or selling the truck by then lol
Anyone point me in a good direction to find a 4.30?
Well right now I usually only tow a small enclosed 6x12 enclosed trailer with a atv ,generators ,coolers and stuff mainly for camping.on the freeways I always have to keep it in tow mode and...
Well after hitting a curb at 50 mph due to a dumb lady that almost T-boned me and wife I now have a bent left rear axle tube and am wanting to get some inputs and suggestions on what ratio would be...
Thanks guys, I guess I pretty much had most of it already figured but wanted to be sure, now I need to get a date and some room in my shop to start this. Home owners association loves me so I can't...
well after much thought of selling my kit ive decided my truck would just not be the same ,so now i am looking into going front mount setup mainily because of when it rains no matter what i do the...
Well like they say all good things must come to a end , especially with a baby on the way . Just testing the waters and trying to figure out a FAIR price for my turbo system , its is complete with...
I actually have my own atv buisness here in katy texas , if any of yall need anything just let me know, new or used parts
this is my 08 420 4x4,
ok i installed new checkballs , Transgo hd2, Transgo seperator plate, all aluminum pistons, corvette servo,new solinoids, and it works like a charm , im very happy with the HD2 kit, was easy to...
yes that snap ring has to be seated all the way in, i used a pry bar and wedged it between the servo cover and body and pushed it down. before you re-install the servo make sure ALL the orings on the...
no you just have to remove heat shield on the passenger side of the trans, i think they are 10mm bolts and then you will see the servo cover.
heres a good video for you to look at...
yes the servo on the right side of the transmission is the servo for 2nd and 4th. you can install the vette servo and see what it does, might tighten things up a bit, like i said servo is easy ,just...
its the first place i would start , the servo is easy to remove , otherwise it could be the 2-4 band wich would require to pull the trans.
yes the pin, im wondering if it might be in my oil bucket ? maybe it fell out when i removed it this time. ill have to look in it and if its not there then ill be worried, that pin should not just...
Common failures on 4L60E, symptom < cause > any possible repair:
1. Slow, slipping or no reverse: “lo-reverse” clutches are worn out, fluid leak in the reverse apply circuit, or broken sunshell. It...
Thanks, im still going to get new check balls tomorrow and a few orings for the solinoids , well i just noticed metal flake in my oil pan, almost like a candy paint job on a car. when i assembled it...
ok got one question, the check ball in the 1-2 valve body hole is the one thats bigger,almost twice the size of the others, i put a new transgo seperator plate and gaskets on it and reused all the...
ok wellllllll i took it apart and noticed some how i put both valve body gaskets on the trans side then put the seperator plate lol, i have no clue how i managed this but i did it, well i checked the...
ok well i drove it around and when i get on it a bit it has a slipping in 2nd ? i put the orings and spring in the vette servo today with 1 shim and it feels like my stall(hughes 2500hd) converter is...