Here you go.
http://i47.photobucket.com/albums/f165/SRT10KLLR/Camaro%20Engine/L92Heads1.jpg
http://i47.photobucket.com/albums/f165/SRT10KLLR/Camaro%20Engine/L92Heads2.jpg
They are the Stage...
Type: Posts; User: SRT10KLLR
Here you go.
http://i47.photobucket.com/albums/f165/SRT10KLLR/Camaro%20Engine/L92Heads1.jpg
http://i47.photobucket.com/albums/f165/SRT10KLLR/Camaro%20Engine/L92Heads2.jpg
They are the Stage...
I have a set of WCCH L92 heads and a set of L99 heads with some port matching and a valve job for sale. Both came off a 2010 Camaro. They are both being gone through by Richard at WCCH. He will be...
I went to the track last month to test out the 150 shot but ran into electrical issues so I did not feel like swapping to the DR's. I ran down the 1/4 on the street tires(Goodyear 295/65/16) and...
Stock48 also took it out to a 1/4 track and ran 10.8 that way. Here is some info on that pass and his current setup.
http://www.performancetrucks.net/forums/showthread.php?t=485488
BTW, I...
Yeh, my cousin in Mexico bought Parish's truck a couple years ago. It kept spliting the block so he replaced it with a LSX block that is now a 427 and some 6 bolt heads from WCCH. He lost interest on...
Still have these.
Bump.
Why not just buy 60lb Multech II truck injectors so you don't have to cut/splice/solder anything and you don't need any spacers either. Also, you don't need to adjust the min pulse width, battery...
Thanks, for the props. Come on guys someone buy one or both of these or I will be forced to use them in a twin build, lol.
Well took it up another notch on the juice. Yesterday I dropped the 100 pills in and did some runs on the street to check fuel pressure and A/F(O2 sensor crapped out though) and it would dip for a...
I have two GT-76 turbos for sale that I bought from STS. They both have 76mm/103mm compressor wheels and P-Trim turbine wheels. One has a .96 A/R and has about 500 miles on it. I had a company go...
The two on the left are Garrett 3686's for the Camaro, the two in the middle are the Garrett GT-76's I was going to use on the Silverado truck but have them for sale right now to get one big turbo...
Tial is making turbo housings now too. I just got some Garrett/HTA 3586's with Tial stainless steel turbine housings.
Come on guys make me an offer I can't refuse, lol.
I just received the two...
I race my brothers 2010 Camaro and my best was a 12.81 with just headers and tune. Then with a CAI installed I ran a 12.59.
Will be finding out shortly.
I am glad it did and hope it continues...
You will also need a wastegate, silicone couplers, t-bolt clams, oil pump(if rear mount), oil lines etc.
I have two Garrett GT-76's for sale if you need one. I was going to go twin but my kit is...
Will try and get some new ones in the day and some with a little juice too.
I would get a 3000+ stall but I am going to be installing a turbo and was told not to stall or gear it to high. So, stock 3.73's and my 2600 stall for now.
BTW, what do you run in the Camaro?
...
So you gained 1.2 with a 150 shot or roughly .4 for every 50 shot. So I am headed in the right direction so far. Can't wait to spray 200.
My 60ft times did not change at all for me. I have the...
What is everyone gaining in ET with spray?
I went to the track the other day and was running 13.5 all motor. I sprayed a 50 shot for the first time and it netted me a .5 sec improvement in the...
I did a little burnout a couple months ago. I did not want to foot(power) brake at all just hit the gas off idle. I had to let off before the 2-3 shift because it started going sideways a little bit....
I just installed a kit on the Silvy and also did not want to drill any holes. You can run the main feed line through the frame rail all the way to the back and up and through the boxed openings used...
Thanks, I got almost the same advice from another member so I know it is sound advice.
Here is what he wrote "hotside piping 2" in and 3" downpipes
coldside 2.5" into a single 3" will be fine...
Anyone?
My plan was to use one Garrett GT-76 turbo for my Silverado with a 408 but people said the turbine side was too small and would cause high back pressure so I decided to make it a twin setup...
Do these fit perfectly in the space for an extra battery on the 99-07 trucks like the aluminum one?