Search:

Lt285/75R16 or 285/70R17 depending on you stock wheel size.. Will fit no problems, maybe a minor tbar adjustment. They might rub slightly at the rear plastic inner fender, but you can tie that back a...

Thanks for that. Im thinking about this cam just to keep the bottom end torque strong under 3000rpm. If you guys think I will still gain some bottom end with something like a tr220?? Let me know and...

Just wondering what everyone thinks about the comp 212/218 265 cams?? For my 2500HD 6.0L. I tow and dd with it. Im not sure why I would not go with the high lift version?? there isnt much diff...

Can anyone tell me if the Dynatech long tubes will fit a 2001 2500hd with the 6.0l?? Site says from 07-10 but I didnt think their was really any major changes except the addition of a y pipe instead...

Got it no problems after thinking for a lunch break. It the bolts start spinning?? Take your air hammer and hit the head of the bolt until the bed nut breaks free. Then cut of bolt and pull nut out...

Because while in the shop and with a full tank of fuel!! Its a whole lot easier!! Bolt removal pending that is!

could a week fuel pump cause this?

Have to do the fuel pump on my pig tomorrow! She died on the way home today. Anyhow tried to get the bed bolts out quickly before dinner while at the shop and 2 of the fron bolts are just spinning....

Just wondering what you guys are running for timing advance in your LQ4's? Its in a 01 2500HD with the 4L80E and 4.11 gears. The stock timing table looks pretty pathetic? Im planning on running 87...

Weld a washer and then a nut to them. A good mig welder and competent user will have no issues. The heat breaks the bond and then you can carefully and painfully sometimes turn them out. It worked...

If its only in od and Lockup? try unlocking the converter and see if it is still there? If not then you may have a converter problem. Did you change it with the tranny rebuild? I had a similiar...

The reason people dont like K@N is because they cant read or follow instructions. They have a great warranty and will even cantact The dealers if you have any problems with your warranty etc. They...

Ok kinda what I thought. Stick with Delco!! Now anyone notice any mpg difference between brands? Old and new etc?

Looking to replace my upstream O2 sensors in my 01 2500hd 6.0l. Just looking on suggestions for what brand to use? Acdelco/Bosch/Ngk etc. I know some ecms are picky with these kinds of things. Thanks...

Will they fit on a 2500hd 4x4? with or without the Y. Its an 01. Interested.

Sorry but mostly stock truck and engine. Will be gettind a tune from Nelson but want to know if I should do the kit first? CAI/Exhaust and future headers maybe cam etc. Tow about 5000-7000lbs mostly...

Wondering what to add to my recently rebuilt 4L80e? What shift kit? Servo etc. Its been built with upgraded cluthes and has a jr pressure release valve. But would like some firmer shifts and I tow...

Great thanks. Live in Canada so I hope its not a long phone call LOL. Not sure about the 91tune. Its pricey and Ill be towing etc?

Going to order a tune from Nelsons soon. Its for an 01 2500hd 6.0L 4x4 with a rebuilt 4L80e. Just some quick questions? Anyone had a tune in this type of vehicle and what gains did you see? I dd it...

What did it take to do the swap? Ecm pin and flywheel and tune? Freind is thinking about doing this to his. Thanks

Just wondering if you guys know wether or not you can remove the oil pan from an 01 2500hd 4x4 with Lq4 without droping the fron diff? Looks like there might be enough room but not sure? Want to...

Ok thanks! but does anyone know if this will help to get rid of the lifter tick etc?

Just wondering if anyone has any advice/experiance with adjusting your stock lifter preload? Currently stock Lq4 with consistant inconsistant lifter tick. Seems mostly on the #1bank. Im thinking of...

Thanks guys!! I was thinking that its the oil pickup tube? I haven owned the truck for all those K's So dont know how long its been there? Yes it does come and go etc. Ive read that the Oil pickup...

Will it actually go away if I replace the oil pickup o-ring? Truck has 185000km second owner and I know its not really causing any problems but i dont like noises that shouldnt be there? Any tips?...