Search:

Type: Posts; User: truckpuller

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    3,535

    Pictures of the heads to truckpuller@joink.com.

    Pictures of the heads to truckpuller@joink.com.
  2. Replies
    6
    Views
    2,602

    I'm sure the heads being milled have nothing to...

    I'm sure the heads being milled have nothing to do with my problem and, yes, I did put the right length pushrods and shimmed the stands accordingly.

    I don't have an actual temp gauge wired up...
  3. Replies
    6
    Views
    2,602

    I got a funny look from my machinist , but he...

    I got a funny look from my machinist , but he done it anyway.
  4. Replies
    6
    Views
    2,602

    bogging 6.0

    Just finished my 6.0 swap into my 86 chevy one ton 4x4. It is hooked to the factory turbo 400 tranny. It is an lq4 with the heads milled .040, comp cam 220/220 .55x .55x on 114ls, truck manifolds...
  5. Replies
    2
    Views
    1,607

    Fan extension?

    My fan in my 86 6.0 conversion needs pushed out some then it would work perfect with my factory fan shroud. It also hits my elbow coming off the tb. Does anybody make an extender for this or will I...
  6. Replies
    4
    Views
    1,691

    Going to check my grounds this afternoon. That...

    Going to check my grounds this afternoon. That is probably my problem since my solenoid for the other stuff is doing the same thing.
  7. Replies
    4
    Views
    1,691

    Red Connector C2: or GREEN Pin 9 - Dk...

    Red Connector C2: or GREEN

    Pin 9 - Dk Green/White - Fuel Pump Relay Control - This wire the PCM supplies 12v+ to control a relay for fuel pump. PCM will turn on the fuel pump for 2 seconds at...
  8. Replies
    4
    Views
    1,691

    relay question

    Finally built a fire in my 6.0 swap this evening. Its in an 86 military 1 ton 4x4 chevy. I have a couple electrical problems though. My fuel pump relay will not work properly. If i use a jumper...
  9. Replies
    1
    Views
    1,670

    wiring harness questions

    Reworking my harness and have a couple questions. The engine is an 02 lq4. Its going in an 86 chevy truck backed by a th400 non lock up transmission. I'm using a 99 wiring harness from a 4.8. Is...
  10. Replies
    3
    Views
    1,776

    Wiring harness Question

    Reworking my harness and have a couple questions. The engine is an 02 lq4. Its going in an 86 chevy truck backed by a th400 non lock up transmission. I'm using a 99 wiring harness from a 4.8. Is...
  11. Replies
    3
    Views
    3,363

    73-87 4x4 6.0 exhaust manifolds

    Does anyone know if exhaust manifolds off an 02 corvette will fit between the frame rails of a 86 4x4 chevy? They are the long header looking manifolds.
  12. Replies
    35
    Views
    8,416

    Favorite tuner/harness builder?

    I've got an lq4 that I'm trying to get ready for my ex-military one ton 4x4. I know Nelson seems to be the favorite but I wondered if anybody has had any luck with anybody else? The engine is a...
  13. Replies
    9
    Views
    3,456

    Well I finally got to pick my "new" truck up this...

    Well I finally got to pick my "new" truck up this week and luckily it was all I expected it to be plus some. Drives like a new one! Fixed a fuel leak on the old 6.2 and runs like a top. I've...
  14. Replies
    9
    Views
    3,456

    Will I be happy with a 6.0?

    I recently purchased a new farm truck. It is an 86 military 1.25 ton pickup with 10,000 miles. For those that don't know it is a 6.2 diesel, turbo 400, 208, 4.56 gear. My old truck was a 427bbc,...
Results 1 to 14 of 14