Hello,
Been a long time since last been on here,
Wanted to check in and give some update. I’ve had the truck parked for the last year and half. I have finally put it back together from redoing the...
Type: Posts; User: chvz99
Hello,
Been a long time since last been on here,
Wanted to check in and give some update. I’ve had the truck parked for the last year and half. I have finally put it back together from redoing the...
the gas pedal is for a 08 tbss , I made a bracket that allowed me to bolt it in the stock bolt holes, I changed the pad from my stock pedal since the new one looked funny compared to the brake pedal,
hey guys its been about a year since I did the swap and I'm trying to get my tach to work, at first It work was reading wrong but it work for about a week until we made some adjustment on the tune so...
this switch only engages when the pressure In the condenser gets beyond a certain point/ ac on. I had to look at the stock a/c controls to figure it out. for anyone that will use this mode make sure...
just wanted to share some info,
if you have efans and want them to turn on when the a/c is on,
you can use the a/c switch mounted in the a/c condenser 95 and older,
just provide ground to one...
I would of liked for gm to had come with this engine sooner, they only upgraded the heads for the 6 bolt lsx and the crankshaft for the lsa they left the same connecting rods as in my engine they...
hey art-
why not run an afermarket headunit and use this that u posted. u wont need as many converter boxes, i have an ipod cable on my with the aux cable so i can use my phone aswell and listen on...
hey guys, im trying to get my a/c working before it gets real hot here in tx,
what would be a better choice for an a/c compressor i have no experience with any of this 2,
some say r4 is a POS, too...
I have dynatech high flow cats, and was still showing low efficiency codes for the cats,,,,
Put some sparkplug foulers on the rear o2s and it pass,, obd2 test.
That really sucks man,
another use if any one wants to just show off, i had them hooked on my 97 tahoe to my alarm system to where i could controll thm with the alarm remote on / off.
think as if some one is walking in...
i have them on my truck the reason i installed them is for my type of work, you can have strobe ligths for construction type of work, and they must be in the clear side of the lens on your ligths, I...
I didnt/dont have flasing leds, my taillights were led kind and got stolen.
I only have clear strobe lights
I had been collecting parts for awhile now, finally decided to do it and pull it off in two days, lol ,,, i do have a spare 14 bolt axle 2wd with drum assembly 6 and 8 lug ,and no shafts that will be...
i have police strobe ligths on my truck, front and back / my l.e.d tailigths got stolen so only have the front now, its fun when cars actually pull over lol
i have a ls3 corvette windage tray for sale
4/6 would be a little too much as im trying to stay close to a 32'' tire migth put some black 24s later down the road, the truck was 8 lug :)
thanks guys,
I did a 6 lug conversion on the truck and added disc brakes on the rear at the same time.
whats your opinion on the height should I lowered 2/3? its been lowered 2'' already on the back
what do you guys think of my obs crewcab on nnbs texas edition wheels
dallas differential sound familiar i think i bougth an axle shaft fromm them some years back, will give them a call n see, do you guys think 4.10s will be ok with a 2400-2600 stall
my setup is...
any one knows a good place to have a rear axle build in the dfw area, looking to install tru trac ,4.10 and all new bearings in 14 bolt sf.
I also have a 14 bolt sf 8 lug that would be posting for...
it shouldn't go up and down at idle unless your rpm's are. maybe do and oil change with a better oil filter and remove those rigged oil lines / and install a bypass plate if your not going to use a...
blue connector e67 pin 54
and gray connector pin 49
it does send the ground signal but the relay will start buzzing getting hot.
and if i apply ground to the relay where the ecm wire goes it will...
im in texas. you will have to use components from the year motor u install. 4 o2s, cats purge solenoid ,evaporation canister .i install the canister at the stock location on my truck and the bracket...
the truck is a 99.
the ecm im using is an e67 with an 08 tbss system.
im thinking my tuner set the fans settings as pwm corvette style instead of ls1 (relay controlled) thats why my ecm ground...