Search:

Type: Posts; User: Nak

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    145
    Views
    418,917

    Sticky: Yeah, there were a few wires I kept from the old...

    Yeah, there were a few wires I kept from the old engine harness. You need a set of wiring diagrams from your 94. There's a lot of work figuring out what you want/need to keep. Then you painstakingly...
  2. Replies
    1
    Views
    2,917

    Thanks for your service Marine Raider1! If...

    Thanks for your service Marine Raider1!

    If cost is an issue I'd rebuild the 5.3. That saves you a lot of headaches and a million little parts that end up nickel and dimeing you to death. Take the...
  3. Replies
    4
    Views
    5,241

    Depends on your 4L60. My '92 was not computer...

    Depends on your 4L60. My '92 was not computer controlled and had a vacuum hookup for kick down. I'm not sure how I would have got it running right, but I'm sure it's doable. 4L80 is a nice trans, but...
  4. Replies
    2
    Views
    3,750

    First off, read my swap thread listed in my...

    First off, read my swap thread listed in my signature, very similar to yours.

    Second, your stock tranny has kickdown based of vacuum I believe? I could be wrong there, but there will be issues...
  5. You don't mention if you're putting in a Gen III...

    You don't mention if you're putting in a Gen III or Gen IV motor. For Gen 4 you don't use a tac module, just the pedal. The pedal from a 2012 Yukon fits and works great, It's a lot easier than trying...
  6. Replies
    93
    Views
    36,967

    Here's the latest version of my dash. Needle...

    Here's the latest version of my dash. Needle positions and numbers are random and nonsensical in these screen shots. The upper four gauges turn red individually when out of safe operating limits. The...
  7. Replies
    93
    Views
    36,967

    Well it's been a couple of months... The truck is...

    Well it's been a couple of months... The truck is running outstanding. I switched mufflers to a different Dynomax VT; simply outstanding sound now. Very quiet until you get on it and then a very nice...
  8. Replies
    93
    Views
    36,967

    The internal linkage was not hooked up. Why that...

    The internal linkage was not hooked up. Why that was so, I don't know. I do know that Stricker Auto on Ebay sold me the trans and it was supposed to be out of a running vehicle. It could not have...
  9. Replies
    93
    Views
    36,967

    Here's an early rendering of the gauge cluster...

    Here's an early rendering of the gauge cluster I'm working on:9842
  10. Replies
    93
    Views
    36,967

    I thought being somewhat slow off the line was...

    I thought being somewhat slow off the line was probably torque management. I raised the torque limit in all the gears way up and disabled traction control. HOLY CRAP! It's fast off the line now. ...
  11. Replies
    93
    Views
    36,967

    IT'S ALIVE!!! Turns out it was the internal...

    IT'S ALIVE!!!

    Turns out it was the internal shift linkage. Interesting, because the trans was supposed to have come from a running vehicle. Not possible. I'll get videos up, but here are my...
  12. Replies
    93
    Views
    36,967

    True, but I'm checking oil off the ALDL link....

    True, but I'm checking oil off the ALDL link. Turns out that was an issue with HPTuners, as another scan tool sees the oil press and temp just fine. I'm getting Fuel level, oil press, etc in to the...
  13. Replies
    93
    Views
    36,967

    Already fixed everything but the tranny not going...

    Already fixed everything but the tranny not going into gear. As far as that goes, It's either an OS compatibility between the TCM and the ECM--most likely I think--or a VIN incompatibility--Less...
  14. Replies
    93
    Views
    36,967

    Started her up tonight! Some problems though......

    Started her up tonight! Some problems though... First, I get a DTC "No comm with TCM" and the transmission won't go into gear. I'm thinking I'll have to have my TCM reflashed at a dealer. Second, I...
  15. Replies
    93
    Views
    36,967

    :) Getting close. I filled and calibrated the...

    :) Getting close. I filled and calibrated the fuel tank, installed the intake and a few other details. I pressurized the fuel system and no leaks! Yay!

    Here are the calibration values for a 1998...
  16. Replies
    3
    Views
    1,786

    I hate problems like this! Very tough. First,...

    I hate problems like this! Very tough.

    First, you need to try a known good scanner. If the EFI tuner was able to communicate I can't think of any reason your scanner wouldn't, unless it's broken....
  17. Not sure why you're having an issue... On my '92...

    Not sure why you're having an issue... On my '92 with 1" setback I have plenty of clearance between the firewall and the rear plugs... In fact, the rear plugs are easier to access than they were with...
  18. Replies
    93
    Views
    36,967

    Had a few problems. I was missing a couple of...

    Had a few problems. I was missing a couple of breakouts on the harness, not a big deal--easy enough to add. Then I realized my fuel sender was wrong. I switched to a '98 tank to get the 40-250 ohms...
  19. Okey dokey, I flashed a new tune with a basic...

    Okey dokey, I flashed a new tune with a basic linear fuel sender calibration reversed from normal. Then I hooked it up with multiple resistors and varied the resistance. HPtuners shows the fuel level...
  20. Actually my plans require the ECM to get the...

    Actually my plans require the ECM to get the fuel. My truck is a '92, and the factory gauge won't work with the '98 fuel sender. (I ran a '98 tank to get a fitting for the vapor pressure sensor and a...
  21. Calling anyone who has swapped a 2004+ engine into a 1998-2003 rig

    From 1998 till somewhere around 2004 GM fuel senders were 40 ohms empty and 250 ohms full. Then they reversed it to 40 ohms full - 250 ohms empty.

    I swapped a 2012 L94 6.2L into an older rig. The...
  22. Replies
    93
    Views
    36,967

    Fuel tank & system is done. The 2012 plug for the...

    Fuel tank & system is done. The 2012 plug for the fuel tank vapor pressure sensor had to be trimmed to fit the 1998 fuel sender/pump module. Should still be weatherproof. Hoping to start her up...
  23. Replies
    93
    Views
    36,967

    Thanks for that. Too late for me--mine's already...

    Thanks for that. Too late for me--mine's already modified--but that should help folks reading this.

    I'm making minimal progress. First I had to work on the remodel, then I got called out of town,...
  24. Replies
    93
    Views
    36,967

    The framers are done with the second stage of our...

    The framers are done with the second stage of our remodel, so I was able to clean up the garage over the last two days and get the Blazer back inside. I'll be working on both the remodel and the swap...
  25. Replies
    93
    Views
    36,967

    The harness finally came fro Motech!...

    The harness finally came fro Motech! Unfortunately, I'm now gone on a work trip for a week, then I have to do the wiring on our remodel. The earliest I'll be able to work on the truck will be the...
Results 1 to 25 of 111
Page 1 of 5 1 2 3 4