Search:

Type: Posts; User: bstill

Page 1 of 5 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    22
    Views
    3,267

    I had the same problem. My injectors were clogged.

    I had the same problem. My injectors were clogged.
  2. Replies
    1
    Views
    2,074

    Depends on how hard you plan to push it. Maybe...

    Depends on how hard you plan to push it. Maybe someone with more knowledge than me will chime in on this.

    I run 3/8" supply and return. But I just have a stock cammed 5.3. Wanted to do some type...
  3. Thread: SC Newbie

    by bstill
    Replies
    3
    Views
    596

    Welcome to the forum.

    Welcome to the forum.
  4. Replies
    32
    Views
    4,074

    Wish I could. But I have to shave for my job....

    Wish I could. But I have to shave for my job. Have to wear full face respirators to work in airborne radiation areas.
  5. Replies
    13
    Views
    2,063

    I'm planning on building a turbo kit for my 99....

    I'm planning on building a turbo kit for my 99. I'll be keeping a look out for used parts when the time comes to help keep the budget in check. I have an 80e ready to go in, so I should have no...
  6. Replies
    10
    Views
    2,728

    I've got an old 100 mph cluster out of my 99 if...

    I've got an old 100 mph cluster out of my 99 if you're interested in those. Been sitting on the shelf for a couple years. Worked perfectly when I took it out.
  7. Replies
    87
    Views
    26,260

    No, not on that forum. We have a few close to us....

    No, not on that forum. We have a few close to us. Twitty's Mudbog and Thunder Valley Mudplex being the closest. Haha, I know those are some big shoes to fill but you got to have a goal, right?
  8. Replies
    87
    Views
    26,260

    West Georgia Mud Park. Wish we had something like...

    West Georgia Mud Park. Wish we had something like that closer to me so I could ride my boys. All we have is straight pits, no passengers allowed. I'm ready to build something on rockwells, then I'll...
  9. Replies
    228
    Views
    101,481

    You should make a thread for this so that it can...

    You should make a thread for this so that it can be stickied in the conversion section. Good job. It's nice to see someone think outside the box and save hundreds in the process.
  10. Replies
    35
    Views
    7,379

    .120 over makes it the same size as an ls1. Just...

    .120 over makes it the same size as an ls1. Just look for ls1 pistons.
  11. Replies
    35
    Views
    7,379

    You can use 4.8 flat top pistons for the bump in...

    You can use 4.8 flat top pistons for the bump in compression. Stock rods will be fine. Get some ported 5.3 heads milled to around 60cc. The bump in compression will help your low end torque. A cam...
  12. Replies
    228
    Views
    101,481

    Looking good, man. Keep it up. :thumb:

    Looking good, man. Keep it up. :thumb:
  13. Replies
    15
    Views
    3,673

    I don't have any good water pumps or are you...

    I don't have any good water pumps or are you asking about the 6 water pump bolts? I can check on the bolts but it's doubtful that I have bracket bolts. I'll let you know.
  14. Replies
    15
    Views
    3,673

    Pistons and rods sold.

    Pistons and rods sold.
  15. Replies
    52
    Views
    6,614

    I had the same problem with my blazer. Quite a...

    I had the same problem with my blazer. Quite a difference with ~50 more hp.
  16. Replies
    2
    Views
    1,424

    If you still have cathedral port heads, you'll...

    If you still have cathedral port heads, you'll need one off a tbss or gen IV 5.3/4.8. If your throttle body is drive by cable, you'll need an aftermarket throttle body since gen IVs are drive by wire.
  17. Replies
    2
    Views
    1,259

    Don't know much about the iron heads, but I would...

    Don't know much about the iron heads, but I would get some 243/799 heads if I needed heads for the bump in compression. But since you have 317s already, just mill them .030".
  18. Replies
    5
    Views
    1,937

    I decided on keeping the exhaust on and not...

    I decided on keeping the exhaust on and not running straight pipes. My exhaust is exactly like yours except for the cat and rear o2. It sounds damn good too which is one reason I decided to leave it...
  19. Replies
    5
    Views
    1,937

    No, it's not a daily driver. It's my mud...

    No, it's not a daily driver. It's my mud truck/blazer. I was planning on running a foot of pipe off the collectors and was wondering if it would be enough. Seems like it may be if you're running a 6"...
  20. Replies
    5
    Views
    1,937

    Running straight headers

    I plan on taking the exhaust off my blazer in favor of straight headers. How long of an exhaust pipe do I need to have after the collectors so that the O2s don't go crazy?
  21. Thread: 3.73 to 4.xx?

    by bstill
    Replies
    2
    Views
    1,113

    Yeah, with over 100 more hp and torque, it ought...

    Yeah, with over 100 more hp and torque, it ought to move much better. It's something that I've been wondering about for some time. If the rear end ever goes out, I'll step it up to 4.10s and a...
  22. Replies
    36
    Views
    10,304

    Just get some cheap, ugly ass wheels.

    Just get some cheap, ugly ass wheels.
  23. Thread: 3.73 to 4.xx?

    by bstill
    Replies
    2
    Views
    1,113

    3.73 to 4.xx?

    I know gear questions get asked a lot but I've searched everywhere and couldn't get a definitive answer for my question.

    Currently I have 3.73s with a 30" tire. I will be swapping in an 80e and...
  24. Replies
    16
    Views
    3,046

    Agreed. Good seller. Thanks for the harness and...

    Agreed. Good seller. Thanks for the harness and good luck with the rest.
  25. Replies
    15
    Views
    3,673

    BUMP! Oil pan, windage tray, pickup tube and...

    BUMP! Oil pan, windage tray, pickup tube and bolts sold. For some reason I can't edit my original post. Open to trades too.
Results 1 to 25 of 119
Page 1 of 5 1 2 3 4