Search:

Type: Posts; User: 7two

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    588

    so got the pcm just need a harness that is drive...

    so got the pcm just need a harness that is drive by cable.. bump
  2. Replies
    1
    Views
    588

    Need DBC Engine harness/ pcm

    Converting from dbw to dbc... looking for a harness and pcm
    Correct me if I am wrong.. 2000-2002 4.8, 5.3, 6.0
    I am running a th350 so its not 4L60e 80e specific.
  3. Replies
    1
    Views
    748

    Parting out 36k mile LQ4

    Parting out low mile (36K) LQ4:

    -317 heads less exhaust rockers $250
    -intake w/fuel rail, injectors, and throttle body $150
    -stock engine harness uncut 2006 (6.0/4L80E) W/PCM $150...
  4. Thread: WTB L92s

    by 7two
    Replies
    2
    Views
    595

    fully assembled

    fully assembled
  5. Thread: WTB L92s

    by 7two
    Replies
    2
    Views
    595

    WTB L92s

    Looking for a set of L92s and L76 intake to put on my 6.0 stroker build
  6. Thread: 6.0/4L80E harness

    by 7two
    Replies
    3
    Views
    600

    my bad I have a 04 6.0 4L80.

    my bad I have a 04 6.0 4L80.
  7. Thread: 6.0/4L80E harness

    by 7two
    Replies
    3
    Views
    600

    6.0/4L80E harness

    Looking for a complete engine harness to fit my 6.0 vortec 4L80E
  8. Thread: Will a 4L80E fit?

    by 7two
    Replies
    2
    Views
    1,132

    Will a 4L80E fit?

    I know the section says LSX Truck but.. I want to put a turbo LSx/4L80e in my 94 mustang. Does anyone know if this trans will fit with out hacking up the tunnel?
  9. Replies
    1
    Views
    609

    2003 Z71 stock gears for sale Front and Rear

    These are the stock 3.73's out of a 03 z71 1500. They have aprox 13,000 miles on them and were swapped for 4.56 when i did my lift. I have both front and rear gears. Pics up tonight
  10. Replies
    7
    Views
    977

    if you decide to go with 373s i have a stock set...

    if you decide to go with 373s i have a stock set with 13,000 miles on them from my 2003 z71 front and rear.
  11. Thread: 64 C-10 Swap...

    by 7two
    Replies
    26
    Views
    5,316

    i have a set of doug thorleys on my 72 they may...

    i have a set of doug thorleys on my 72 they may make some for your 63. cheap route would be putting an lsx flange on some big block headers
  12. Replies
    1
    Views
    571

    Free 5.3 motor mounts

    Free motor mounts from a 2002 tahoe with 60,xxx miles they are in good shape.
    http://i39.photobucket.com/albums/e153/lunchbox574/untitled-2.jpg
  13. Replies
    5
    Views
    1,409

    FS:650 Holley Double pumper

    Almost new 650 zinc coated double pumper mechanical choke. Ran it for maybe 200 miles on my 72 c10 as a crutch. Now have 5.3/4l60e :)
    Paid like $415 a couple of months ago take it for $250

    ...
  14. Thread: ses light wiring

    by 7two
    Replies
    3
    Views
    931

    thanks man!

    thanks man!
  15. Thread: ses light wiring

    by 7two
    Replies
    3
    Views
    931

    ses light wiring

    i am nearly complete on my 5.3 4l60e swap in my 72 half ton. i have moddified my stock harness. can anyone tell me which pin the ses light connects to on the pcm. 2002 pcm red and blue. thanks
  16. Replies
    6
    Views
    6,178

    A 2002 truck pan fit in my c10.. Mine is a 72 but...

    A 2002 truck pan fit in my c10.. Mine is a 72 but crossmember is very similar if not the same
  17. Replies
    24
    Views
    13,454

    Sticky: that truck looks familiar where have i seen it...

    that truck looks familiar where have i seen it lol. nice writeup man, you missed out on all the fun with my motor swap
  18. Replies
    18
    Views
    3,032

    Tach wiring for 99+ Vortec/LS1...

    Tach wiring for 99+ Vortec/LS1
  19. Replies
    18
    Views
    3,032

    Found this when I was cruising the net. May be...

    Found this when I was cruising the net. May be your answer for a cheap easy fix on your tach...
  20. Replies
    18
    Views
    3,807

    yup they are early classic mounts they are worth...

    yup they are early classic mounts they are worth the money
  21. Thread: What do you think

    by 7two
    Replies
    6
    Views
    1,216

    What do you think

    I know there are prob. hundreds of posts like these....
    A friend of mine has a comp custom grind for cheap I am interested in stabbing into my 5.3. 216/218 @ .050 with .555/.555 on 114. This will...
  22. Replies
    39
    Views
    29,940

    Sticky: Talked to FLT yesterday asked if they were...

    Talked to FLT yesterday asked if they were working on 6 speed auto technology... The sales rep told me that the controller for these transmissions is integrated into the trans making it ALMOST...
  23. Replies
    9
    Views
    1,469

    oops forgot the link.. 2000 Vortec 4.8/5.3/6.0...

    oops forgot the link.. 2000 Vortec 4.8/5.3/6.0 Harness Info
  24. Replies
    9
    Views
    1,469

    Here is a useful site about converting gen III...

    Here is a useful site about converting gen III harness to standalone. It has pin outs by year, pictures, intructions. I just did mine it was alot of work but it turned out well. Like said above if...
  25. Replies
    9
    Views
    5,585

    17 dollars for the pair..

    17 dollars for the pair..
Results 1 to 25 of 40
Page 1 of 2 1 2