Search:

Type: Posts; User: Mf2racer

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    28
    Views
    4,561

    I have USA standard 4:56 from rons and they do...

    I have USA standard 4:56 from rons and they do make some noise at certain mph. Beat the crap out of my truck and no issues even though I don't make any power haha.
  2. Replies
    9
    Views
    3,733

    cam and stall! no doubt

    cam and stall! no doubt
  3. Replies
    9
    Views
    2,138

    Guess I should have mentioned that, it is a rcsb...

    Guess I should have mentioned that, it is a rcsb 2wd one piece driveshaft.
  4. Replies
    9
    Views
    2,138

    Well this points me towards a bent housing. I...

    Well this points me towards a bent housing. I just don't know what I would have done to bend it. Guess its time to find a 14bolt or dana 60. Wish I would have kept the 60 I had out of my Ford. ...
  5. Replies
    9
    Views
    2,138

    Truck is on 2in shackles only. Angles are near...

    Truck is on 2in shackles only. Angles are near equal but opposite. I might try dropping the trans some though.
  6. Replies
    9
    Views
    2,138

    No, no hoop yet. Planning on building one...

    No, no hoop yet. Planning on building one though. I don't drive the truck much but, would still like to not see it go up in flames.
  7. Replies
    9
    Views
    2,138

    High Speed Vibration

    Well guys I need some help.

    Here is the whole back story.

    A few years back when I grenaded my 4l60e I went ahead and replaced my u-joints at the advice of my father even though the stock ones...
  8. Depending on tire size I would just stay with the...

    Depending on tire size I would just stay with the 3.73s that you already have.
  9. Replies
    19
    Views
    4,758

    It's best to try to keep everything grounded to...

    It's best to try to keep everything grounded to one point. Some car audio enthusiast go as far as running a ground wire straight from the battery to amps, iirc tests have shown better efficiency. ...
  10. Thread: Driveshaft?

    by Mf2racer
    Replies
    8
    Views
    1,924

    Not sure where I would find a box that large? ...

    Not sure where I would find a box that large? Shipping should only be $30-40
  11. Thread: Driveshaft?

    by Mf2racer
    Replies
    8
    Views
    1,924

    I have one, but I am in Indiana.....it came out...

    I have one, but I am in Indiana.....it came out of a 1999 rcsb 1500
  12. Replies
    15
    Views
    4,626

    4.56

    4.56
  13. Thread: Clunk noise

    by Mf2racer
    Replies
    6
    Views
    1,453

    Start by putting some grease on the splines of...

    Start by putting some grease on the splines of the yoke in the trans see if it helps any.
  14. Replies
    21
    Views
    4,804

    I learned the hard way. I believe you either...

    I learned the hard way. I believe you either remove all of the tm or none of it. I removed just partial tm and broke the sunshell in the trans 6 weeks later. Now I have no tm and its great.
  15. Replies
    10
    Views
    10,174

    Should have spent the extra cash on the audioque...

    Should have spent the extra cash on the audioque amp. Lift the seat if you have to, the greater airspace will help. Big 3 upgrade and a better battery are my only suggestions. Sounds like a good...
  16. Replies
    629
    Views
    138,019

    Thanks for all my 10bolt stuff...It came really...

    Thanks for all my 10bolt stuff...It came really fast. I should have asked for some shirts and stickers lol...opps
  17. Replies
    5
    Views
    1,062

    Yea, we have a take a part here, but they never...

    Yea, we have a take a part here, but they never have any nbs trucks.
  18. Replies
    5
    Views
    1,062

    Junk yard wants $160 for a stock one around here.

    Junk yard wants $160 for a stock one around here.
  19. Replies
    5
    Views
    1,062

    Stock 2wd sway bar.

    Looking for a stock or aftermarket front sway bar for a 2wd nbs silverado thanks.
  20. Replies
    32
    Views
    4,794

    I had a problem with my u-joints binding you...

    I had a problem with my u-joints binding you might check that.
  21. Replies
    20
    Views
    3,162

    Looked it up Belltech part number 4302.

    Looked it up Belltech part number 4302.
  22. Replies
    20
    Views
    3,162

    I believe Quik on here has trimmed springs you...

    I believe Quik on here has trimmed springs you could ask him to be forsure on the process.
  23. Replies
    20
    Views
    3,162

    The spring rate can change. So just no torches. ...

    The spring rate can change. So just no torches. Use a cut off wheel or sawsall and take it slow and go back and forth from spring to spring.
  24. Replies
    20
    Views
    3,162

    What I have read it is a slow process. I would...

    What I have read it is a slow process. I would start with a 1/4 or 1/2 of a coil then check and cut more if needed. Just gotta keep them cool while you cut.
  25. Replies
    20
    Views
    3,162

    You could probably get away with cutting them...

    You could probably get away with cutting them which is what I'm planning to do for my 1/2 drop. You could also get a 2inch drop coil with a 1inch spacer. The other option is those sexy coilovers...
Results 1 to 25 of 115
Page 1 of 5 1 2 3 4