Search:

Type: Posts; User: jetmech

Page 1 of 5 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    2,283

    Torque pattern for 4L80 pan

    Does anyone know what the torque pattern is for the 4L80 pan bolts? Also, do I need to lubricate the gasket with trans fluid prior to installation?
  2. Replies
    91
    Views
    30,531

    Bump for a good seller. I bought one of these for...

    Bump for a good seller. I bought one of these for my 4L80 swap, works great :burnrub:
  3. Replies
    9
    Views
    7,610

    I think I'm in love!

    I think I'm in love!
  4. Replies
    9
    Views
    7,610

    The truck in my garage, with the following...

    The truck in my garage, with the following upgrades:

    ~ 427 LSX
    ~ Twin turbos
    ~ 4 Link
    ~ and a few other things I'm probably forgetting
  5. Replies
    50
    Views
    30,433

    The engine compartment is a real mess, I know,...

    The engine compartment is a real mess, I know, but I'm in the process of tuning (having Allen tune it, actually) and cleaning everything up. it's still a work in progress, but running strong none the...
  6. Replies
    50
    Views
    30,433

    I've been working through some issues, but...

    I've been working through some issues, but solving them none the less. I should be able to get some pics uploaded later today.
  7. Thread: Engine grounds

    by jetmech
    Replies
    16
    Views
    8,337

    It turns out the tune I had was causing all the...

    It turns out the tune I had was causing all the issues - the clowns here in south Florida don't know what they're doing. Allen, thanks for rescuing me. The truck is running really well now - one data...
  8. Thread: Engine grounds

    by jetmech
    Replies
    16
    Views
    8,337

    Would you be able to tell by looking at the tune?...

    Would you be able to tell by looking at the tune? At this point I'm willing to send you the PCM and get a second opinion. The truck takes throttle just fine when sitting in the driveway revving the...
  9. Thread: Engine grounds

    by jetmech
    Replies
    16
    Views
    8,337

    It stumbles like crazy, I hit the throttle and...

    It stumbles like crazy, I hit the throttle and hold my foot steady, yet the truck behaves as though I am tapping the throttle. I can make it into second gear, beyond that I lose all faith in the...
  10. Thread: Engine grounds

    by jetmech
    Replies
    16
    Views
    8,337

    Got it. Next question: If the truck is in...

    Got it. Next question:

    If the truck is in "limp mode", would it behave as I have described in my original post? I've heard of a bad knock sensor throwing the PCM into limp mode and causing a great...
  11. Thread: Engine grounds

    by jetmech
    Replies
    16
    Views
    8,337

    I've run SD tunes in the past and never seen a...

    I've run SD tunes in the past and never seen a MAF code. That is what has me concerned.
  12. Thread: Engine grounds

    by jetmech
    Replies
    16
    Views
    8,337

    P0054 - H02S Heater resistance (bank 1 sensor 2)...

    P0054 - H02S Heater resistance (bank 1 sensor 2)
    P0060 - H02S Heater resistance (bank 2 sensor 2)
    P0102 - Mass or volume air flow circuit low input
    P0103 - Mass or volume air flow circuit high...
  13. Replies
    1
    Views
    3,361

    4L80e input shaft speed sensor PCM pins

    I've been having electrical issues so I've been looking at wiring diagrams a lot lately. During my studies of these diagrams, I noticed that some describe a RED retainer on the PCM connector where my...
  14. Thread: Engine grounds

    by jetmech
    Replies
    16
    Views
    8,337

    Engine grounds

    I'm having an electrical problem which I am almost positive is a ground issue. If I am not mistaken, 4 grounds attach to the block - (1) large gauge wire (looks like 4 or 2 AWG) which attaches to the...
  15. Thread: 4L80 swap

    by jetmech
    Replies
    3
    Views
    3,068

    4L80 swap

    My truck is an '06 and came with a 4L60. I hear some trucks came with a separate trans controller if a 4L80 is factory equipped. So what do you do if you swap from a 4L60 to a 4L80 and your truck...
  16. Thread: Arizona

    by jetmech
    Replies
    2
    Views
    2,896

    Arizona

    I may be moving to Arizona and I'm trying to figure out what kind of emissions laws, if any, the state of Arizona has. Any Arizona residents on this site?
  17. Replies
    50
    Views
    30,433

    Update coming soon...

    Update coming soon...
  18. Thread: belt?

    by jetmech
    Replies
    1
    Views
    1,440

    belt?

    Any recommendations for a good serpentine belt that will handle a lot of power?
  19. Replies
    2
    Views
    2,425

    sold

    sold
  20. Replies
    1
    Views
    4,948

    Duramax MAP sensor

    I picked up a Duramax MAP sensor, part # 12623671 (3 bar I think). I plan to run up to about 18 psi on this build. Will this MAP sensor work well for what I'm trying to do?
  21. Replies
    2
    Views
    2,425

    Price drop, $800 plus shipping

    Price drop, $800 plus shipping
  22. Replies
    2
    Views
    2,425

    4L60E, low miles

    I'm swapping to a 4L80E, so this transmission needs a home. This 4L60E was built less than 3 years ago and has only seen about 10,000 miles of use. It's a stock transmission with a shift kit. Asking...
  23. Replies
    3
    Views
    2,117

    96 lbs injectors and fuel rails?

    What is a good set of 95 lbs/hr injectors (@ 4 bar) or something close to that? Preferably a set with an impedance that will work well with the factory VCM. Also, what are a good set of aftermarket...
  24. Replies
    6
    Views
    2,926

    Favorite country songs?

    Let's face it, stereotypically a person who drives a Chevy truck will at least have some interest in country music. Country may not always be my first choice, but I do enjoy it. So as the title says,...
  25. Replies
    7
    Views
    3,036

    This is my first rodeo with the mighty 4L80, so I...

    This is my first rodeo with the mighty 4L80, so I am in uncharted territory of sorts. Still, part of the fun is figuring out how something else works!
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4