ls1 in 94 Silverado update and pics

Well, finally got started.. got most of the fuel system done except running the lines (cant find the hose anywhere local).. Waiting to hear back from Allen on the harness.. Motor mounts should be here anyday now..
enough of the blah blah.. he are some pics..

http://ridnlow.curtroyer.com/bt1.JPG


http://ridnlow.curtroyer.com/bt2.JPG



http://ridnlow.curtroyer.com/bt3.JPG


http://ridnlow.curtroyer.com/bt4.JPG

http://ridnlow.curtroyer.com/bt5.JPG


http://ridnlow.curtroyer.com/bt6.JPG


http://ridnlow.curtroyer.com/bt7.JPG


http://ridnlow.curtroyer.com/bt8.JPG


http://ridnlow.curtroyer.com/bt9.JPG

Sweet....thanks for the pics!!

Alota work ahead of you. But once your done, :burnout: :burnout: :burnout:

its cool to see the progress though. stay on it you will be done in no time.

finished the fuel stuff up tonight.. just waiting on harness and motor mounts.. im sure thats when the real fun begins..

Ah... memories... :cool: Escalade front on that truck, huh? :thumb: Gonna be sweet when you're done!

Good progress! I went ahead & removed the front core support & bumper when I was at that stage. It was easy & gave me alot better access to fitting the motor mounts, etc. It also allowed me to degrease & brush on black epoxy "POR15" frame/suspension paint. Not that I'm suggesting YOU do that or anything(?) :eek: LOL...Looks great, keep up the good work. Gar

Yea, the core support and stuff is coming off probably tomorrow or this weekend sometime.. We are also going to paint all the frame and the engine bay, once we figure out what part of the harness can go and what part needs to stay.. thanks for the kind words.. im sure ill run into plenty more problems but this site has been a ton of help and I know i can find the answers..

ridnlow...Question? In the picture of your LS1 motor, on the ground, to the left of the engine...What exactly is that thin aluminum piece of trim? I have that same piece left over from my install & I'll be damned if I can remember where the hell that thing goes!!!??? Do you know? Thanks, Gar

I asked my brother (he does most of wrench turning) and he said he had to take that off the manifold in order to get to the motor mounts.. I guess it is a heat shield of some kind??

very good progress, your miles ahead of me. Keep on her :thumb:

ridnlow..in the first picture, that is the pump that you put into the tank right? and then do you also have an external fuel pump? thanks

<div class='quotetop'>QUOTE(c1500 &#064; Oct 12 2006, 12&#58;01 AM) [snapback]68987[/snapback]</div>

Quote:

---

ridnlow..in the first picture, that is the pump that you put into the tank right? and then do you also have an external fuel pump? thanks
[/b]

---

yea that is the one we put in the tank.. No i do not have an external one.. The motor will stay stock for quite some time.. so I hope the in tank should be suffice..

Sweet&#33; I have the same leveling beam for setting motors. Does the paint peal off of yours from the lower wheel when you tilt the motor back? If so make sure you have all of the holes covered. Good luck&#33;

ridnlow...Any new progress you&#39;d like to share? :cool: Gar

i can&#39;t wait to be diong what your doing? nice work. what did you do for the motor mounts

Motor is in..we got kind of impatient and didnt paint, so we may pull it again and paint it, just trying to get it running for now.. Got the notice that Allen shipped out my harness today so that should be in... Ill be sure to take some picture of the harness and the process of putting it on..

Skates on the motor mounts, we went with S & P.. had to do a little work to get it to go but wasnt to bad..