Twin T70 turbo kit 3700.00

Why go single when you can have Twins? This is our flip manifold twin kit with the turbo facing forward and tight in the enginebay. We think this is the best looking twin kit out here. The waste gates are routed into the downpipes, with flex joints making it alot easier to bolt up. I would say 95% complete.
Kit comes with
2) MasterPower T70 .63a/r
2) vband clamps
2) 38mm waster gates (cooper gaskets, no blow outs)
2) stainless steel Mid pipe sections with gaskets
2) stainless steel down pipes, drivers side is routed under the truck to the passenger side. and merges into a custom Y.
1) 2.5 x 4 merge pipe. We are using a 4" diesel exhaust on this truck
Custom air to water intercooler. We took 2 singles and cut them apart and rewelded to make 1..Hanging infront of the engine but you could move it somewhere else, just requires more piping and couplers.
1) complete set ofsilicone couplers, clamps and piping.

Things you will need.
3) 2.5 exhaust band clamps.
1) 4.0 exhaust band clamp.
2) air filters / kits
2) oil line kits (turbo have our billet drain fittings attached.
finsih rigid mounting IC.. IC has temp brackets on there right now.


Normally this kit would be around 4200.00 as it sits, but its Christmas time so 3700.00 + freight and I am sure somone has been thinking about doing twins. :hyper2:

http://www.trickperformanceproducts....n/100_3568.JPG


http://www.trickperformanceproducts....d/100_3358.jpg

http://www.trickperformanceproducts....d/100_3359.jpg
http://www.trickperformanceproducts....d/100_3360.jpg



http://www.trickperformanceproducts....n/100_3569.JPG

http://www.trickperformanceproducts....d/100_3372.JPG

http://www.trickperformanceproducts....d/100_3371.JPG


http://www.trickperformanceproducts....d/100_3370.JPG

http://www.trickperformanceproducts....d/100_3361.jpg


http://www.trickperformanceproducts....n/100_3570.JPG

http://www.trickperformanceproducts....n/100_3573.JPG

http://www.trickperformanceproducts....n/100_3572.JPG


http://www.trickperformanceproducts....n/100_3571.JPG

OMG, Nice work and price. Have you tested these on a the GMT900 trucks? I can't afford to buy one right now but I can dream, right? :lol:

Ugh if this was for sale in exactly a year I would be all over this..

Quote:

---

Originally Posted by RedHeartbeat

OMG, Nice work and price. Have you tested these on a the GMT900 trucks? I can't afford to buy one right now but I can dream, right? :lol:

---

I can dream too, right? Wish i knew that it would be that clean on my 86!

bump for a good deal

nice kit

I want one and even though that's a KILLER price, all my funds are focused on college :sigh:

I want it but my funds are focused on a 4l80 so I can drive my truck again.

Awesome seller. I know first hand.

Quote:

---

Originally Posted by jetmech

I want one and even though that's a KILLER price, all my funds are focused on college :sigh:

---

You and me both man.

quit school and buy it lol

How laggy would it be in a Lq4?
Too much boost for a 5.3L right?

would be good on a 6.0, or a 5.3.... too much boost? dont understand that, kinda like too much money... or getting laid too much... lol

Is the kit upgradeable to bigger turbos or bigger housings? How hard are the plug wires to run with this kit? What kind of hp with the intercooler handle?

did the kit ever run? any numbers?

Quote:

---

Originally Posted by White Devil

How laggy would it be in a Lq4?
Too much boost for a 5.3L right?

---

Lag depends on cam, tune, convertor etc. Lots of variable. The small exhaust housing will lesson any lag. But lag is a form a traction controll. lol too much boost not sure what you mean. You could run 5lbs if you want to. Be a waste but could be done.

Quote:

---

Originally Posted by mean05

Is the kit upgradeable to bigger turbos or bigger housings? How hard are the plug wires to run with this kit? What kind of hp with the intercooler handle?

---

Housing can be swapped out and or go to 76MM turbos if that is needed. HP cores I beleive are 4.5 x 4.5 x 10 each been a while since I messed with them.

Quote:

---

Originally Posted by TurboMic

did the kit ever run? any numbers?

---

This kit has not been fired up on the truck. All parts are new and still have some of there boxes laying around.
I need to buy some more equipment for the shop and needed to sale something. Trucks been in the air a few months so figured I would sale the kit off of it. Things it needs are blow off oil lines water lines a few clamps and air filters. If the kit does not find a new home, we will finsih it out completely and go have some fun. The plug wires we have not crossed yet but there are several options out there from reroute like old school sbc...

This kit was going with our 370 we built. just do not have time to install that engine with this kit, a new 80e and get it all tuned up for the next shoot out. Not to mention the new stuff I need to buy so I need to send this down the road.:)

Will it fit a 2002 4x4?

Can not say, the mock up truck is a 2wd. The only difference would be in the driverside crossover. Which is 2pc's so it would be easier to get around if it hit that driver shaft.

Found the radiator we were going to modify for the HX today. It will be added to the list of parts supplied. ;)
And
Discount one of our water tanks.


http://www.trickperformanceproducts....d/100_3361.jpg

special tank is not anodized.
http://www.trickperformanceproducts....anks/black.jpg

i need this...DBRods and I were talking about the go ahead to build a 408 stroker...single turbo...but I need this....must resist.

No you must no resist. lol We have a new single idea sure would like to build for someone. ;)

If someone is wanting the hot pipes only I can let these go for.
1800.00+freight with out the Y fitting at the bottom.. 1900 + freight with that adaptor.

http://www.trickperformanceproducts....n/100_3571.JPG

I noticed that you didn't have any cooling fans for the radiator.... guess you will have to rig up some e-fans with no shroud?

And how much boost is this thing capable of?

15+ is no problem. It really depends how hard you want to push the system. Yes we have coolant fans just took them out easier to work around.

They are in this pic.

http://www.trickperformanceproducts....d/100_3359.jpg

seriously no one has bought this?!?!?!?!?!?!?!

Not yet you interested? :)

I'm very interested but I don't have 3700 right now

damn I wish I could make this happen

I want this so bad...about to wear my mouse looking at this thread

If I do not find a home soon, I will finish the kit and get this truck running. There is a race coming up I would like to go to..:).

Nice looking setup man!

Err...bump

----------------
Now playing: Dope - Bitch
via FoxyTunes

Bump. Someone going to SAR in feb. Need a turbo? Equipment is starting to show up. Anyone interested drop a pm.

Be expecting a PM in the next few hours!! :)

Mitch you buying it? lol

Sending a PM and buying something are two different things....

Don't be sneaky ass hole

This is a great price on a high quality twin turbo kit.. Ricks stuff is super nice and a Great fit ... Not sure how its lasted this long...

Not a sneaky if pms are announced. LOL ;)

Thanks Casey, yea been up for a click or so but its all good. Just got bills rolling in and need to get this shop equip'd out finished and done. Tired of looking at half finsihed walls, and working around everything. ugggggg

I think this kit is a great set up, clean fit. And should make a HUGE amount of power with the right engine combo.'
I have to keep moving on it, would like to come to SAR in FEb. if nothing more then to see customers, other rides and set ups, and maybe show off some new stuff.

SOLD!!!!!!!! and shipped.

Quote:

---

Originally Posted by Turbo6.0L

SOLD!!!!!!!! and shipped.

---

Cough Cough to Corn Cobb.....

:rolly: