2005 6.0 burning oil BAD on startup...PCV valve issue?

I have Been dealing with the truck smoking more and more each time on startup. It gets worse and worse each time you drive it for long periods and then let it sit. According to most people they say it is the PCV valve in the drivers valve cover...and I am guessing they are right because I popped my valve cover off (2005) and you can tell theres a baffle built into it. But I am wondering if there is any other way to fix this issue other than replaceing the valve cover. I am quite sure it is PCV related because I looked down the intake and there is a huge pool of oil just sitting right inside of it. Right now I have the valve cover soaking in brake cleaner

May want to look into valve seals also...

There's a TSB for my '09 Escalade and it was doing the same thing, burning oil. However it wasn't the pcv system, it was the valve cover design.
Anyway, without going into details, I did this instead of buying a new valve cover:

took both valve cover ports to a catch can, then out the catch can into the cai tube so i don't smell any fumes. they get recirculated back into the engine.

Quote:

---

Originally Posted by farmtruc

There's a TSB for my '09 Escalade and it was doing the same thing, burning oil. However it wasn't the pcv system, it was the valve cover design.
Anyway, without going into details, I did this instead of buying a new valve cover:

took both valve cover ports to a catch can, then out the catch can into the cai tube so i don't smell any fumes. they get recirculated back into the engine.

---

Ya I saw there was a catch can setup that kind of looks like an A/C accumulator. I was hoping there was another option rather than doing the catch can setup, or buying new valve covers.

Quote:

---

Originally Posted by bangbangskeetskeet

May want to look into valve seals also...

---

Thats what I originally thought...until i saw all the oil inside of the intake.

I went the cheap route, but it works. Go to home depot, get you one of those water separators for the air compressor.
They use 1/4 " barb fittings on each side. Get a T connector, route both line into the T, into the separator, then into the cai tube.
Done!
the catch can is directional, so pay attention to the flow.

My intake was full of oil as well, about a cup worth.

Quote:

---

Originally Posted by farmtruc

I went the cheap route, but it works. Go to home depot, get you one of those water separators for the air compressor.
They use 1/4 " barb fittings on each side. Get a T connector, route both line into the T, into the separator, then into the cai tube.
Done!
the catch can is directional, so pay attention to the flow.

My intake was full of oil as well, about a cup worth.

---

Ya mine is terrible...i mean B-A-D! I would say i got about a quarter to half a quart out of mine. It would blow smoke for atleast 5 minutes on a cold startup. The only problem is I want to keep my engine bay clean looking. Guess I will have to buy the new style valve covers if I want to keep the bay clean :-(. I just started it up and it still smoked after cleaning all the gunk out of the built in pcv valve in the cover, and driving it really hard to make sure there was no more oil in the intake...ugh. There has to be a better solution you and I cant be the only ones with the problem this bad. My motor has less than 100k on it!

IF the issue is the same as my truck; the cause was an over active lifter squirting on the valve cover right in the pcv area. The vacuum would suck oil up into the hose, draining in the intake.
If you want a cleaner look, just take both valve covers to the intake tube and that way, all you've done with add two hoses and you won't smell exhaust fumes.

Would the "over active lifter" be the one that ticks really bad on my truck on startup? lol

that's funny, but probably not; more likely it's not pumping up with oil.
time to pull the engine and forged it, 383.